Hama EWS-3000 Mode D'emploi page 6

Note
• Initial setup takes approx. 3 minutes.
• During the connection attempt, the measuring station radio
symbol (1) will ash.
• Do not press any buttons during setup. Otherwise, values may
not be transmitted correctly and there is a risk of value errors
and inaccuracies.
• The setup process is completed when the indoor (6) and
outdoor (4) measurement data is displayed
• If the base station still does not receive a signal from the
measuring station, press and hold the Channel button (24) for
approx. 3 seconds to start the manual search for the signal.
6.2. Basic and manual settings
Automatic setting using the DCF signal
• After the rst time the base station is switched on and successful
transmission is established between the base station and the
measuring station, the clock will automatically search for a DCF
signal. During the search, the wireless symbol (14) will ash.
Display (14)
Display ashing
Displayed continuously
No display
• If the station still does not receive a signal, press and hold the –
button (23) for approx. 3 seconds to start the manual search for
the DCF signal. The radio symbol (14) will start to ash.
Note – Time settings
• The search process takes about 7 minutes. If the search fails,
it ends and is repeated at the next clock hour.
The radio symbol (14) goes out.
• In the meantime you can, however, set the time and the
date manually.
• The clock automatically continues to search for the DCF signal
on a daily basis (between 1:00 a.m. and 5:00 a.m.) to correct
any deviations. If the signal is received successfully, the
manually set time and date are overwritten.
• Press and hold the – button (23) again for approx. 3 seconds to
stop the manual search.
Note – Summer time
The clock automatically switches to summer time. DST appears
on the display as long as summer time is activated.
(Manual) settings
• Press and hold the – button (23) for approx. 3 seconds to stop
the search for the DCF signal. The wireless symbol (8) goes out
and you can set the time manually.
4
Searching for the DCF signal
Active
Successful –
signal is being received
Inactive
• Press and hold the MODE button (20) for approx. 3 seconds to
make the following settings one after the other:
• 12/24 hour format
• Time zone
• Hours (12)
• Minutes (12)
• Year
• Month (8)
• Day (7)
• Weekday (10)
• To select the individual values, press the + button (22) or the –
button (23) and con rm each selection by pressing the MODE
button (20).
• Press the MODE button (20) immediately to adopt the set value
displayed and to skip onwards.
• If you do not make an entry for 20 seconds, you automatically
exit setup mode.
Note – Time zone
• The DCF signal can be received over long distances, but
always transmits the current Central European Time in
Germany. Make sure you set the time difference in countries
with another time zone.
• If you are in Moscow, for example, the time is 3 hours later
than in Germany. This means that you should set +3 for
the time zone. The clock then automatically sets the time
to 3 hours after the DCF signal received or relative to the
manually set time.
Note – Weekday
You can choose from German (GE), English (EN), Danish (DA),
Dutch (DU), Italian (IT), Spanish (SP) and French (FR) for the
weekday display.
Celsius/Fahrenheit
Press the – button (23) to switch between °C and °F for the
temperature display.
Alarm
Note – Alarm
• When activated, alarm mode 1 only triggers an alarm signal
on weekdays (Monday to Friday).
• When activated, alarm mode 2 only triggers an alarm signal
on Saturday and Sunday.
The A1 or A2 alarm symbol will appear in the seconds position of
the time display during setting.
• Press the ALARM button (21) once or twice to display alarm
A1 or A2.
• Press and hold the ALARM button (21) for approx. 3 seconds
to set the time of the alarm displayed. The hours display begins
to ash.
• Press the + button (22) or the – button (23) to select the hour
for the alarm time and con rm your selection by pressing the
ALARM button (21). The minutes display begins to ash.