DRL BADGE HAND MOVIE REMOTE Mode D'emploi page 41

English
General
Comfort temperature
reference
Boost time
Keyboard lock
User settings
Eco reduction level
Frost protection
Minimum Comfort
temperature limitation
Maximum Comfort
temperature limitation
Ambient temperature
limitation
Surface temperature
limitation
Maximum Boost time
Installer Settings
Open window detection
Optimisation function
PIN code protection
PIN code value
Advanced Installer Settings
Heating with
ambient or surface
temperature setpoint
Surface temperature
sensor calibration
Ambient temperature
sensor calibration
Radiator power
To exit the settings, press
15. Troubleshooting
First of all, make sure that the Receiver and the Remote Control are
paired (see pairing check).
The receiver does not work:
- No power supply to the receiver: check the switch or fuse in the
power supply circuit.
- Check the batteries of the thermostat to which it is connected.
- Another emitter may cause an inference that prevents the
connection between thermostat and receiver from working properly.
Radio transmission does not work properly:
1 - The receiver is not picking up the code sent by the emitter.
Ambient Surface
temperature temperature
adjustment adjustment
19 °C 60 °C
60 min 60 min
Disabled Disabled
-3.5 °C -30 °C
7 °C 10 °C
7 °C 20 °C
30 °C 80 °C
30 °C 30 °C
80 °C 80 °C
60 min 60 min
Enabled Enabled
Comfort option Comfort option
Disabled Disabled
0000 0000
Heating with Heating
ambient with surface
temperature temperature
setpoint setpoint
0.0 0.0
0.0 0.0
500 W 500 W
3 times.
- Replace the transmitter batteries (refer to their instruction manual).
- Delete the stored code, refer to section "Resetting the relay" (see
page 3).
- Pair the transmitter with a receiver again, refer to section "Pairing"
(see page 2).
2 - No pairing between receiver and thermostat or remote control.
- Delete the stored code, refer to section "Resetting the relay" (see
page 3).
3 - Pair the transmitter with a receiver again, refer to section "Pairing"
(see page 2).
- Radio wave interference affects the receiver or remote control (e.g.
from radio amateurs, a TV screen, etc.): - Move the emitter away
from the affected area.
- Try to move the receiver or the source of the interference away.
Lost connection between receiver and thermostat or remote control:
- After more than 3 hours, the RED light starts flashing continuously
and the next cycle begins - the contact switches to ON status (i.e.
closed between terminals 2 and 3) for 1 minute and then switches
to OFF status (i.e. closed between terminals 1 and 2) for 9 minutes.
Then the protection mode is enabled, the red light flashes once
every 2 seconds.
- Delete the stored code, refer to section "Resetting the relay" (see
page 3).
- Pair the transmitter with a receiver again, refer to section "Pairing"
(see page 2). The receiver is out of the emitter range.
- Move the transmitter closer to the receiver, for optimal operation
the receiver must be positioned in the centre of the house, flat or
area to be covered.
If the problem persists, contact Technical Service.
DECLARATION OF CONFORMITY
The Company Cordivari S.r.l. with registered office in Morro
D'Oro (TE), Zona Industriale Pagliare, hereby declares, under
its own responsibility, that the household electric radiators listed
in par.2 comply with following rules:
EN 60335-1:2012 + AC:2014 +
A11:2014 +A13:2017 + A1:2019
+ A14:2019 + A2:2019
EN 60335-2-43:2003 + A1:2006
+ A2:2008
EN 60335-2-30:2009 + A11:2012
+ A1:2020 2012
EN 62233:2008 + AC:2008
EN IEC 61000-3-2:2019 +
A1:2021
EN 61000-3-3:2013 + A1:2019
EN 61000-4-2:2009
EN 61000-4-3:2020
and therefore meet the essential requirements of the following
European Regulations and Directives:
Directive 2014/53/EU
Directive 2014/35/EU
Directive 2014/30/EU
Directive 2012/19/EU
Directive 2009/125/EC
Directive 2011/65/EU
2017/2102/EU
Commission Regulation (EU) 2015/1188
Morro D'Oro, 15/07/2022
- 36 -
EN 61000-4-4:2012
EN 61000-4-5:2014 + A1:2017
EN 61000-4-6:2014 + corr.
August:2015
EN 61000-4-11:2020
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN 55032:2015
ETSI EN 301 489-17:2020
ETSI EN 301 489-1:2019
ETSI EN 301 489-3:2019
ETSI EN 300 440:2018
amended by 2015/863/EU
Cav. Ercole Cordivari
Amministratore unico
Cod. 1910000000381 - nv00
and