Publicité
Les langues disponibles
Les langues disponibles
EN
English
INSTRUCTION MANUAL
Machine Type:
This product is designed for installing and removing threaded
fasteners in wood, metal and plastic. The use of spare parts/
accessories other than those originally supplied by the
manufacturer may result in a drop in performance and/or
increased maintenance / noise level / vibrations, and as the
result, the full cancellation of the manufacturer's liability. No
other use permitted. For professional use only.
Air Supply Requirements
1. Supply tool with 90 psig (6.3 bar) of clean, dry air. Higher
pressure drastically reduces tool life.
2. Connect tool to air line using pipe, hose and fitting sizes
shown in the diagram below.
3/8" (10mm)
10' (3m) MAX
1/4 NPT
Lubrication
1. Use an air line lubricator with SAE #10 oil, adjusted to
two (2) drops per minute. If an air line lubricator cannot be
used, add air motor oil to the inlet once a day.
2. For gearing and clutch, use grease containing molybdenum
disulfide such as Chicago Pneumatic CA131898 [14 oz
(395 g)]. Grease clutch every 12,000 screws.
Torque adjustment
Shut Off Clutch: Grip the tool around the motor case and
press the tool into the fixing that is to be tightened. The
motor will start and tighten the fixing to the required torque
set by adjusting the tensions on the Clutch spring. At this
point the internal drive is disengaged and the air to the
motor cut off.
Roller Clutch: Grip the tool then press onto the fixing that
is to be tightened and depress the throttle control. The
motor will start and tighten the fixing to the required torque
set by adjusting the tensions on the Clutch spring. Release
the throttle control and remove tool from fixing.
Maintenance
1. After first year, disassemble and inspect air motor and
impacting clutch every three (3) months if the tool is used
every day. Replace damaged or worn parts.
2. High wear parts are underlined in the parts list.
Original Instructions
Copyright 2010, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the contents or
part thereof is prohibited. This applies in particular to trademarks, model
denominations, part numbers and drawings. Use only authorized parts.
Any damage or malfunction caused by the use of unauthorized parts is
not covered by Warranty or Product Liability.
1/2" (12mm)
CA048362 (1/2") NPT
CA048361 (1/2") NPT
90
0
130
1/2" (12mm)
CA048360 (1/2") NPT
Technical Data
1/4" (6.4mm) Spindle
Air pressure 90 psi (6.3 bar)
Free Speed: 1000rpm(CP2611, CP2621); 1800rpm(CP2622);
1700rpm(CP2612, CP2623)
Torque Range: 1.0-7.5 Nm(8.8-66.4 in. Lb)(CP2611); 1.0-
6.0 Nm(8.8-53 in. Lb)(CP2612); 0.8-6.5 Nm(7-57.5 in. Lb)
(CP2621); 0.5-4.5 Nm(4.4-39.8 in. Lb)(CP2622); 1.5-5.5
Nm(13.3-48.6 in. Lb)(CP2623)
Air Consumption: 21.2 cfm(10.0l/s)(CP2611, CP2612);
30.9 cfm(14.6l/s)(CP2621); 29 cfm(13.7 l/s)(CP2622); 27.7
cfm(13.1 l/s)(CP2623)
Weight: 2.4Lb (1.1 Kg)(CP2611); 1.99Lb (0.9 Kg)(CP2612);
1.8 Lb(0.8 Kg)(CP2621, CP2622, CP2623)
Noise & Vibration Declaration*
Sound pressure level 80 dB(A)(CP2611); 77 dB(A)(CP2612);
76 dB(A)(CP2621); 75dB(A)(CP2622); 78 dB(A)(CP2623) free
speed, uncertainty 3 dB(A), in accordance with ISO 15744-
2002. For sound power, add 11 dB(A).
Vibration value <2.5 m/s
Declaration of noise and vibration emission
All values are current as of the date of this publication. For the
latest information please visit cp.com.
These declared values were obtained by laboratory type testing
in accordance with the stated standards and are suitable for
comparison with the declared values of other tools tested in
accordance with the same standards. These declared values are
not adequate for use in risk assessments and values measured in
individual work places may be higher. The actual exposure values
and risk of harm experienced by an individual user are unique
and depend upon the way the user works, the workpiece and
the workstation design, as well upon the exposure time and the
physical condition of the user.
We, Chicago Pneumatic, cannot be held liable for the
consequences of using the declared values, instead of values
reflecting the actual exposure, in an individual risk assessment in a
work place situation over which we have no control.
This tool may cause hand-arm vibration syndrome if its use is
not adequately managed. An EU guide to managing hand-arm
vibration can be found at http://www.humanvibration.com/EU/
VIBGUIDE.htm
We recommend a programme of health surveillance to detect early
symptoms which may relate to noise or vibration exposure, so that
management procedures can be modified to help prevent future
impairment.
MANUFACTURER'S LIMITED WARRANTY
Limited Warranty:
The "Products" of the Chicago Pneumatic Tool
Co. LLC ("CP") are warranted to be free from defects in material and
workmanship for one year from the date of purchase. This Warranty
applies only to Products purchased new from CP or its authorized dealers.
Of course, this Warranty does not apply to products which have been
abused, misused, modified, or repaired by someone other than CP or its
Authorized Service Representatives. If a CP Product proves defective in
material or workmanship within one year after purchase, return it to any
CP Factory Service Center or Authorized Service Center for CP tools,
transportation prepaid, enclosing your name and address, adequate
proof of date of purchase, and a short description of the defect. CP will,
at its option, repair or replace defective Products free of charge. Repairs
or replacements are warranted as described above for the remainder of
the original warranty period. CP's sole liability and your exclusive remedy
under this Warranty is limited to repair or replacement of the defective
Product. (There Are No Other Warranties Expressed Or Implied And
CP Shall Not Be Liable For Incidental, Consequential, Or Special
Damages, Or Any Other Damages, Costs Or Expenses Excepting
Only The Cost Or Expense Of Repair Or Replacement As Described
Above.)
CP26 Series
Screwdrivers
, re. ISO 28927-2.
2
Publicité
