Publicité
Les langues disponibles
Les langues disponibles
6. Cut the biscuit slots as described above.
7. Adjust the fence up by a distance equal to the desired offset.
Use the scale to read the setting.
8. Cut the biscuit slots as described above.
Edge Mitre Joints (Fig. T1–T4)
Outside surfaces aligned
1. Arrange the workpieces as they are to be assembled.
2. Mark the biscuit centres on the outside of the joint.
3. Set the fence angle to 90 °.
4. Adjust the fence to locate the biscuit toward the inside
of the joint where the workpiece is thicker. Select the
appropriate biscuit size (Fig. T2).
5. Clamp the workpiece and align the tool as shown (Fig. T3).
6. Cut the biscuit slots as described above.
Inside Surfaces Aligned
1. Arrange the workpieces as they are to be assembled.
2. Mark the biscuit centres on the inside of the joint.
3. Set the fence angle to 45 °.
4. Adjust the fence to locate the biscuit toward the inside
of the joint where the workpiece is thicker. Select the
appropriate biscuit size.
5. Clamp the workpiece and align the tool as shown (Fig. T4).
6. Cut the biscuit slots as described above.
T‑Joints (Fig. U1–U5)
This type of joints is commonly used to attach shelves to side
panels (Fig. U1).
1. Place the workpieces on a flat surface as they are to be
assembled (as an upside down T).
2. Mark the biscuit centres on the shelf piece.
3. Lightly mark the top of the shelf on the side panel (Fig. U2).
4. Clamp the fence on top of the side panel, aligning the end
of the shelf with the line (Fig. U3).
5. Select the appropriate biscuit size.
6. Set the fence to 0 °.
7. Align the tool with the biscuit marks using the markings on
the tool base.
8. Make a vertical (Fig. U4) and a horizontal (Fig. U5) cut at
each of the biscuit locations.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
C
Lubrication
Your power tool requires no additional lubrication.
D
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked
w
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to local
provisions. Further information is available at www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails to produce
sufficient power on jobs which were easily done before. At the end of
its technical life, discard it with due care for our environment:
•
Run the battery pack down completely, then remove it from
the tool.
•
Li‑Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
EngLIsh
WALT recommended
e
41
Publicité
