Milwaukee M18 FUEL 2757-20 Manuel De L'utilisateur page 5

OPERATION
Always remove battery pack before
WARNING
changing or removing accesso-
ries. Only use accessories specifically recom-
mended for this tool. Others may be hazardous.
To reduce the risk of injury, wear safety goggles
or glasses with side shields.
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete stop before using the
control switch.
Push for
Forward
PUSH TO CENTER TO LOCK
1. For forward (clockwise) rotation, push the control
switch in the direction shown. Check the direction
of rotation before use.
2. For reverse (counterclockwise) rotation, push the
control switch in the direction shown. Check the
direction of rotation before use.
3. To lock the trigger, push the control switch to the
center position. The trigger will not work when the
control switch is in the locked position.
Always remove the battery pack before performing
maintenance or changing accessories. Always
lock the trigger or remove the battery pack before
storing the tool and any time the tool is not in use.
Selecting Speed
(Cat. No.2706-20)
The speed selector is on top of the motor housing.
Allow the tool to come to a complete stop before
changing speeds. See "Applications" for recom-
mended speeds under various conditions.
1. For Low speed, push the speed selector to display
"1".
2. For High speed, push the speed selector to display
"2".
Selecting Action
(Cat. No. 2706-20)
1. To use the hammer-drilling
mode, rotate the application se-
lector collar until the hammer
symbol appears in line with
the arrow. Apply pressure to the
bit to engage the hammering
mechanism.
NOTE: The number selected on the torque selec-
tor collar has no effect on operation of the drill in
this mode.
NOTE: When using carbide bits, do not use water
to settle dust. Do not attempt to drill through steel
reinforcing rods. This will damage the carbide bits.
2. To use the driving screws mode
rotate the application selector
collar until the drive symbol
appears in line with the arrow.
Then rotate the torque selector
collar until the desired clutch set-
ting appears in line with the arrow.
The adjustable clutch, when properly adjusted, will
slip at a preset torque to prevent driving the screw
too deep into different materials and to prevent
damage to the screw or tool.
The torque specifications shown here are approximate
values obtained with a fully charged battery pack.
Clutch
Setting
1
2
3
4
5
6
7
8
9
10
11
Push for
12
Reverse
13
NOTE: Because the settings shown in the table are
only a guide, use a piece of scrap material to test
the different clutch settings before driving screws
into the workpiece.
3. To use the drilling only mode,
rotate the application selector
collar until the drill symbol
appears in line with the arrow.
NOTE: The number selected on
the torque selector collar has no
effect on operation of the drill in
this mode.
4. To use the Mode Selector
buttons, rotate the application
selector collar until the wireless
symbol
the arrow.
NOTE: The number selected on
the torque selector collar has no effect on opera-
tion of the drill in this mode. Hammer-drilling is not
available in this mode.
Allow the tool to come to a complete stop before
changing modes. Press the selector button
between the settings.Select wireless
the default settings via the ONE-KEY App on your
smart device.
2706-20
High
Low
2757-20
5
in. lbs Applications
30
35 Small screws in softwood.
40
45
50
Medium screws in softwood or
55
small screws in hardwood.
60
65
70
Large screws in softwoods. Me-
75
dium screws in hardwood or large
80
screws in hardwood with pilot hole.
85
90
appears in line with
Default Max RPM
Setting 1 Setting 2 Setting 3 Setting 4
1 200 1 450
300 375
850 1 500
to cycle
to change
1 700 2 000
425 500
2 100 3 000