Milwaukee M18 FUEL 2757-20 Manuel De L'utilisateur page 4

SPECIFICATIONS
Volts.............................................................. 18 DC
Battery Type .................................................M18™
Charger Type................................................M18™
Recommended Ambient
Operating Temperature ......................0°F to 125°F
Cat. No. ..................................................... 2706-20
No Load RPM .......................................Low 0 - 550
BPM .................................................High 0 - 32000
Steel ................................................................. 1/2"
Wood
Flat Bit ....................................................... 1-1/2"
Auger Bit .................................................... 1-1/2"
Hole Saw ......................................................... 3"
Screws ...................................................... Ø 3/8"
Masonry ............................................................ 5/8"
Cat. No. ..................................................... 2757-20
RPM ........................................................... 0 - 3000
IPM ............................................................ 0 - 3700
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
To reduce the risk of injury, always
WARNING
use a side handle when using a 9.0
Ah or higher capacity battery pack with this tool.
Always brace or hold securely. Ensure side
handle is tightened securely before each use.
Installing the Side Handle
1. To install the side handle,
loosen the side handle grip
until the hooks are far
enough apart to fit into the
slots on the gear case ring.
Position the side handle on
the top, pointing to the left or
right. Tighten the side han-
dle grip until it is secure.
2. To remove the side handle,
loosen the side handle grip
until the side handle can be
removed. Reposition and
tighten securely.
may be hazardous.
Always remove the battery before inserting or remov-
ing bits. Select the proper style and size bit for the job.
This tool is equipped with a spindle lock. The chuck
High 0 - 2000
can be tightened with one hand, creating higher grip
strengths on the bit.
1. To open the chuck jaws, turn the sleeve in the
2. To close the chuck jaws, turn the sleeve in the
3. To remove the bit, turn the sleeve in the counter-
NOTE: A ratcheting sound may be heard when the
chuck is opened or closed. This noise is part of the
locking feature, and does not indicate a problem with
the chuck's operation.
use on impact wrenches and drivers. Other
sockets and accessories might shatter or break
causing injury.
This impact driver is intended for use with drill and
driver bits.
1. To attach an accessory, press the shank into the
2. To remove the accessory, pull out the ring and
Hooks
Slots
To learn more about the ONE-KEY functionality for
this tool, please reference the Quick Start guide in-
cluded with this product or go to milwaukeetool.com/
One-Key. To download the ONE-KEY app, visit the
App Store or Google Play from your smart device.
4
Only use accessories specifically
WARNING
recommended for this tool. Others
Installing Bits
(Cat. No. 2706-20)
counterclockwise direction.
When using drill bits, allow the bit to strike the
bottom of the chuck. Center the bit in the chuck
jaws and lift it about 1/16" off of the bottom.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the hex of the bit.
clockwise direction. The bit is secure when the
chuck makes a ratcheting sound and the sleeve
can not be rotated any further.
clockwise direction.
Use only sockets and other acces-
WARNING
sories specifically designed for
Attaching and Removing Accessories
1/4" Hex Impact Driver
(Cat. No. 2750-20)
hex drive chuck.
remove the accessory. Release the ring.
ONE-KEY™