Product Description And Specifications - Bosch PSR 12-2 Notice Originale

OBJ_BUCH-213-004.book Page 12 Wednesday, June 12, 2013 9:02 AM
12 | English
Safety Warnings for Drills and Screwdriver
 Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
or fastener may contact hidden wiring. Cutting accesso-
ry and fasteners contacting a "live" wire may make ex-
posed metal parts of the power tool "live" and could give
the operator an electric shock.
 Use auxiliary handle(s), if supplied with the tool. Loss
of control can cause personal injury.
 Use appropriate detectors to determine if utility lines
are hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age.
 Switch off the power tool immediately when the tool in-
sert jams. Be prepared for high reaction torque that
can cause kickback. The tool insert jams when:
— the power tool is subject to overload or
— it becomes wedged in the workpiece.
 Before any work on the machine (e. g. maintenance,
changing the tool, etc.) as well as during its transport
and storage, lock the On/Off switch in the off position.
There is danger of injury when the On/Off switch is unin-
tentionally actuated.
 Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position. Unintentional actuation of the On/Off switch can
lead to injuries.
 Hold the machine with a firm grip. High reaction torque
can briefly occur while driving in and loosening screws.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
 Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
Technical Data
Cordless Drill/Driver
Article number
Rated voltage
No-load speed
– 1st gear
– 2nd gear
Max. torque for hard/soft screwdriving application according to
ISO 5393
Max. screw dia.
Max. drilling dia.
– Steel
– Wood
1 609 92A 0A7 | (12.6.13)
 Use only original Bosch batteries with the voltage list-
ed on the nameplate of your power tool. When using oth-
er batteries, e.g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for driving in and loosening screws
as well as for drilling in wood, metal, ceramic and plastic.
The light of this power tool is intended to illuminate the power
tool's direct area of working operation and is not suitable for
household room illumination.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Keyless chuck
2 Torque preselection ring
3 Gear selector
4 Indicator for right rotation
5 Indicator for left rotation
6 Screwdriver bit*
7 Battery unlocking button*
8 Battery pack*
9 "PowerLight"
10 Rotational direction switch
11 On/Off switch
12 Handle (insulated gripping surface)
13 Universal bit holder*
14 Securing screw for keyless chuck
15 Allen Key**
*Accessories shown or described are not part of the standard de-
PSR 12-2 PSR 14,4-2
3 603 J51 5.. 3 603 J51 4..
V= 12
-1
min 0 – 390
-1
min 0 – 1250 0 – 1250
Nm 30/17
mm 8
mm 10
mm 30
PSR 18-2
3 603 J51 3..
14.4 18
0 – 400 0 – 400
0 – 1250
36/22 44/28
8 10
10 12
35 40
Bosch Power Tools