Product Description And Specifications; Intended Use; Product Features; Technical Data - Bosch PSB 18 LI-2 Ergonomic Notice Originale

14 | English
Always start drilling at low speed and with the bit tip
u
in contact with the workpiece. At higher speeds, the bit
is likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do
u
not apply excessive pressure.Bits can bend causing
breakage or loss of control, resulting in personal injury.
Additional safety warnings
Hold the power tool securely. When tightening and
u
loosening screws be prepared for temporarily high torque
reactions.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Switch the power tool off immediately if the applica-
u
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback. The applica-
tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
1 609 92A 4YA | (22.01.2020)
Please observe the illustrations at the beginning of this oper-
ating manual.

Intended use

The power tool is intended for tightening and loosening
screws, as well as for drilling in wood, metal, ceramic and
plastic and for impact drilling in brick, masonry and stone.

Product features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Keyless chuck
(2) Torque presetting ring
(3) Operating mode presetting ring
(4) Gear selector switch
(5) On/off switch
(6) Rotational direction switch
(7) Battery release button
(8) Battery charge indicator
A)
(9) Battery
(10) "PowerLight"
(11) Handle (insulated gripping surface)
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical data

Cordless drill/driver
Article number
Rated voltage
A)
No-load speed
– 1st gear
– 2nd gear
A)
Impact rate
Max. torque, hard/soft screw-
driving application according to
A)
ISO 5393
Max. drilling diameter
– Steel
– Wood
– Masonry
Max. screw diameter
Chuck capacity
Drill spindle thread
Weight according to EPTA-Pro-
A)
cedure 01:2014
Recommended ambient temper-
ature during charging
PSB 18 LI-2
Ergonomic
3 603 JB0 3..
V= 18
–1
min 0–430
–1
min 0–1400
–1
min 0–22500
Nm 32/28
mm 13
mm 38
mm 11
mm 10
mm 1.5–13
1/2"
kg 1.6
°C 0 to +35
Bosch Power Tools