Publicité
Les langues disponibles
Les langues disponibles
Electrical Shock
Hazard
Electrically ground oven.
Connect ground with lO-gauge-minimum solid
copper wire.
Failure to follow these instructions could result
in death, fire or electrical shock.
if codes permit and a separate grounding wire is
used, it is recommended that a qualified electrician
determine that the grounding path and wire gauge
are in accordance with local codes.
Do Not ground to a gas pipe.
Check with a qualified electrician if you are not
sure oven is properly grounded.
Do Not have a fuse in the neutral or grounding
circuit.
Oven must be connected to the proper
electrical voltage and frequency as specified
on the model/serial rating plate. (The
model/serial rating plate is located on the
oven door or on the oven frame.)
[] CONNECT WITH COPPERWIRE ONLY.
[] Models rated from 7,3 to 9,6 kW at 240
volts (5.5 to 7.2 kW at 208 volts) require a
separate 40-ampere circuit. Models rated
at 7.2 kW and below at 240 volts (5.4 kW
and below at 208 volts) require a separate
30-ampere circuit.
[] A time-delay fuse or circuit breaker is
recommended.
[] Connect directly to the fused disconnect
(or circuit breaker box) through flexible,
armored or non-metallic sheathed, copper
cable (with grounding wire).
[] Flexible armored cable from appliance
should be connected directly to junction
box.
[] Fuse both sides of the line.
[] A U.L.-listed conduit connector must be
provided at the junction box.
[] Do Not cut the conduit.
Wire sizes and connections must conform with
the rating of the appliance and to the
requirements of the National Electrical Code,
ANSI/NFPA 70 -- latest edition*, or Canadian
Electrical Code, C22.1-1982 and C22.2 No. 01982
(or latest edition)** and all local codes and
ordinances.
Copies
of the standards
listed
may be obtained
from:
National
Fire Protection
Association
Batterymarch
Park
Quincy,
Massachusetts
02269
** Canadian
Standard
Association
178 Rexdale Boulevard
Etobicoke, Ontario, Canada MgW 1R3
"-I i
iDc,. ,ov.o
1
operation.
C::::::::::D
F
J
_
)
t_
Grasp oven
_
frame to lift
OVER.
I
II
_
power
supply cable
I
Remove
_
shipping
feet.
Use screws to attach
oven to cabinet.
Reattach side
trim.
Remove
trim screws.
Remove side
trim.
oven.
Use
screws
to
attach
oven to
cabinet.
_eattach
side
trim.
Remove side
trim.
Preparation
Excessive Weight Hazard
Use two or more people to move and install
oven.
Failure to follow this instruction can result in
back or other injury.
important: Use both hands to remove oven
doors.
Do Not use handle or any portion of the front
frame or trim for lifting.
Before moving oven across floor, checkthat
oven is on shipping base or slide oven onto
cardboardor hardboard.
Do Not remove shipping feet at the front lower
cornersof oven.
Do Not remove
shipping feet.
[] Turn power supply off. Move oven
close to final position.
• Remove and discard shipping materials,
tape and protective film from the oven.
Do Not remove shipping base or
shipping feet at the front lower corners
of oven. The shipping feet will protect
the lower oven trim until oven is
inserted into cabinet.
• Remove and set aside racks and other
parts from inside oven.
_
power
X
supply cable X
Remove
shipping
feet.
Remove trim
screws.
Remove
OVeR doors.
Replace
over
door
Insert
small
end of pin
here.
Remove trim screw.
Pull trim out.
Pull top of trim
down.
[] Completely open lower oven door.
Insert small end of a door removal pin into
each door hinge. Grasp door handle from the
bottom and gently close door as far as it will
shut. Lift slightly and grasp bottom of door
with other hand. Pull door out at bottom to
remove. Set door aside on protected surface.
Repeat for upper oven door.
,, Remove trim screws attaching right
and left side trim to oven. Grasp the bottom
end of trim and pull away from oven. Slide
top end of trim downward to remove trim
from oven. Take care not to scratch other
surfaces with ends of trim. Set trim and
screws aside on protected surface.
Page 2
Publicité
