Andis LCL Mode D'emploi page 3

A B
SAA Europe
SAA SAA Europe Europe
SAA Europe
F
E
PUSH
BRAZIL
I J
ADJUSTMENT
LEVER
SNAP!
CLIPPING GUIDE
Description Clipping Direction
With hair grain
Standard Andis Blade
Against hair grain
With hair grain
1/8" Attachment Comb
Against hair grain
With hair grain
1/4" Attachment Comb
Against hair grain
With hair grain
3/8" Attachment Comb
Against hair grain
With hair grain
1/2" Attachment Comb
Against hair grain
With hair grain
3/4" Attachment Comb
Against hair grain
With hair grain
1" Attachment Comb
Against hair grain
4
All manuals and user guides at all-guides.com
C D
UK US/MX
UK UK US/MX US/MX
UK US/MX
G H
K L
OIL
Approximate Length of Cut
Fine Coarse
1/16" (1.6 mm) 3/16" (4.8 mm)
1/32" (0.8 mm) 1/8" (3.2 mm)
1/4" (6.4 mm) 3/8" (9.5 mm)
1/8" (3.2 mm) 1/4" (6.4 mm)
3/8" (9.5 mm) 1/2" (12.7 mm)
1/4" (6.4 mm) 3/8" (9.5 mm)
1/2" (12.7 mm) 5/8" (15.9 mm)
3/8" (9.5 mm) 1/2" (12.7 mm)
5/8" (15.9 mm) 7/8" (22.2 mm)
1/2" (12.7 mm) 5/8" (15.9 mm)
7/8" (22.2 mm) 1-1/8" (28.6 mm)
3/4" (19.0 mm) 1" (25.4 mm)
1-1/8" (28.6 mm) 1-3/8" (34.9 mm)
1" (25.4 mm) 1-1/4" (31.8 mm)
CHARGING CLIPPER
The AC adapter is intended for use with Andis Model LCL lithium-ion battery with a rated capacity
of 4.5V 1.2A. Remove the clipper and AC adapter from the carton. Plug the AC adapter into a
100-120V, 50-60 cycle AC outlet, or as noted on the unit. Plug the adapter cord directly into the
receptacle on the bottom of the clipper (Figure G). The clipper ON/OFF switch must be in the OFF
position for the battery to charge. The green light on the clipper will turn ON when the clipper is
charging. When clipper is fully charged, the green light will turn OFF.
The clipper has not been charged at the factory. Please charge the clipper for 3-5 hours
before FIRST use for maximum performance. When battery is fully charged, clipper can be
used for up to 90 minutes of continuous run time. After first use, clipper will fully charge in a
minimum of 2 hours.
FAILURE TO CHARGE
1. Make sure voltage is present at the wall outlet (confirm with an appliance you know is working).
2. Make sure ON/OFF switch on the clipper is OFF.
3. Check to make sure adapter cord is plugged firmly into clipper.
4. If failure to charge still exists, return clipper to Andis or an Andis Authorized Service Station for
examination and repair or replacement.
CORDED OPERATION
If the clipper powers OFF in the middle of a clipping job, the adapter cord can be attached to
continue use in corded operation. When the clipper is running with the adapter cord attached, the
green light will remain ON even if the battery is not fully charged. The clipper will not charge while
in use with the cord attached. After using your Andis clipper, rewrap cord and store in a safe place.
USING THE ATTACHMENT COMBS
(Some models do not have combs and sizes will vary by kit)
You can set the blades for a longer cut by using any of the attachment combs made for your Andis
clipper. The combs mount easily; simply slip the cutter blade teeth into comb and snap the comb
down. To remove, simply snap off (Figures H & I). These attachment combs guide hair into the
blades and give you precise control of hair lengths. The length of trim is indicated on the
attachment comb. Use the chart to find the approximate lengths of cut. Different blade angles
in relation to the skin, thickness and texture of the hair will vary the cutting length.
CLIPPER BLADE ADJUSTMENT
Your Andis adjustable clipper blade set is easy to adjust. From coarse to fine cuts, all that is
needed is a flick of the adjustment lever with your thumb. In the upright position, the blades are
set for the finest, or shortest cuts (Figure J).
USER MAINTENANCE
Cleaning and user maintenance shall not be made by children
without supervision.
The internal mechanism of your motor clipper has been permanently lubricated by the factory.
Other than the recommended maintenance described in this manual, no other maintenance should
be performed, except by Andis Company, or an Andis Authorized Service Station.
BLADE TEMPERATURE
Due to the high speed nature of Andis clippers, please check for blade heat often, especially on
close cutting blades. If blades are too hot, dip the blades only into Andis Blade Care Plus or apply
Andis Cool Care Plus and then Andis Clipper Oil. If you have a detachable blade unit, you can
change your blade in order to maintain a comfortable temperature; using multiple blades of the
same size is popular among groomers.
5