Publicité
Les langues disponibles
Les langues disponibles
13. Never attempt to drive fasteners from both the
inside and outside at the same time. Fasteners
may rip through and/or fly off, presenting a grave
danger.
Repetitive motions hazards
1.
When using a tool for long periods, the operator
may experience discomfort in the hands, arms,
shoulders, neck, or other parts of the body.
2.
While using a tool, the operator should adopt a
suitable but ergonomic posture. Maintain secure
footing and avoid awkward or off-balanced
postures.
3.
If the operator experiences symptoms such as
persistent
or
recurring
throbbing, aching, tingling, numbness, burning
sensation, or stiffness, do not ignore these
warning signs. The operator should consult a
qualified health professional regarding overall
activities.
4.
The continuous use of the tool may cause
repetitive stain injury due to recoil produced by
the tool.
5.
To avoid repetitive strain injury, the operator
should not overreach or use excessive force.
Additionally, the operator should take a rest
when feeling fatigue.
6.
Conduct a risk assessment regarding repetitive
motion hazards. It should focus on muscular-
skeletal disorders and be preferentially based on
the assumption that decreasing fatigue during
work is effective in reducing disorders.
Accessory and consumable hazards
1.
Disconnect the energy supply to the tool, such
as air or gas or battery as applicable, before
changing/replacing
workpiece contact, or making any adjustments.
2.
Use only the sizes and types of accessories that
are provided by the manufacturer.
3.
Use only lubricants recommended in this
manual.
Workplace hazards
1.
Slips, trips and falls are major causes of
workplace injury. Be aware of slippery surfaces
caused by use of the tool and also of trip
hazards caused by the air line hose.
2.
Proceed with additional care in unfamiliar
surroundings. Hidden hazards may exist, such
as electricity or other utility lines.
3.
This tool is not intended for use in potentially
explosive atmospheres and is not insulated from
coming into contact with electric power.
4.
Make sure there are no electrical cables, gas
pipes etc. that could cause a hazard if damaged
by use of the tool.
5.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
6.
There may be local regulations concerning noise
which must be complied with by keeping noise
levels within prescribed limits. In certain cases,
shutters should be used to contain noise.
Dust and exhaust hazards
1.
Always check your surroundings. The air
exhausted from the tool may blow dust or
objects and hit operator and/or bystanders.
2.
Direct the exhaust so as to minimize disturbance
of dust in a dust filled environment.
8
All manuals and user guides at all-guides.com
discomfort,
pain,
accessories
such
3.
If dust or objects are emitted in the work area,
reduce the emission as much as possible to
reduce the health hazards and risk of injury.
Noise hazards
1.
Unprotected exposure to high noise levels can
cause permanent, disabling, hearing loss and
other problems such as tinnitus (ringing,
buzzing, whistling or humming in the ears).
2.
Conduct a risk assessment regarding noise
hazards in the work area and implement
appropriate controls for these hazards.
3.
Appropriate controls to reduce the risk may
include actions such as damping materials to
prevent workpieces from "ringing".
4.
Use appropriate hearing protection.
5.
Operate and maintain the tool as recommended
in these instructions, to prevent an unnecessary
increase in noise levels.
6.
Take noise reduction measures, for example
placing workpieces on sound damping supports.
Vibration hazards
1.
The
vibration
depends on the gripping force, the contact
pressure force, the working direction, the
adjustment of energy supply, the workpiece, the
workpiece support. Conduct a risk assessment
regarding vibration hazards and implement
appropriate controls for these hazards.
2.
Exposure to vibration can cause disabling
damage to the nerves and blood supply of the
hands and arms.
3.
Wear warm clothing when working in cold
conditions, keep your hands warm and dry.
4.
If you experience numbness, tingling, pain or
as
whitening of the skin in your fingers or hands,
seek
medical
occupational
overall activities.
5.
Operate and maintain the tool as recommended
in these instructions, to prevent an unnecessary
increase in vibration levels.
6.
Hold the tool with a light, but safe, grip because
the risk from vibration is generally greater when
the grip force is higher.
Additional warnings for pneumatic tools
1.
Compressed air can cause severe injury.
2.
Always shut off air supply, and disconnect tool
from air supply when not in use.
3.
Always
disconnect
compressed
accessories, making adjustments and/or repairs,
when moving away from an operating area to a
different area.
4.
Keep fingers away from trigger when not
operating the tool and when moving from one
operating position to another.
5.
Never direct compressed air at yourself or
anyone else.
6.
Whipping hoses can cause severe injury. Always
check for damaged or loose hoses or fittings.
7.
Never carry a pneumatic tool by its hose.
8.
Never drag a pneumatic tool by its hose.
9.
When using pneumatic tools, do not exceed the
maximum operating pressure ps max.
emission
during
advice
from
a
health
professional
the
tool
from
air
supply
before
operation
qualified
regarding
the
changing
Publicité
