Publicité
Liens rapides
Publicité
Manuels Connexes pour CAMSO 5000-03-1772-MAN
Sommaire des Matières pour CAMSO 5000-03-1772-MAN
- Page 1 Installation Guidelines Honda 5000-03-1772-MAN VERSION A...
- Page 2 Please read carefully each part of this document as well as the User Manual prior to assembling, installing and using the Track System. CAUTION: Longevity of the Camso Track System’s components is directly linked to the way in which the System is used. Sportive driving, rapid direction changes and repeated fast turns (especially on power steering vehicles) are not advised.
- Page 3 PARTS LIST CAUTION: Before beginning the installation, make sure that you have received all the components included in the parts lists below. ITEM PART # DESCRIPTION 1004-03-0330 FRONT BRACKET KIT ANTI-ROTATION FRONT BRACKET - LH ANTI-ROTATION FRONT BRACKET - RH FRONT COVER - LH FRONT COVER - RH 1033-10-0065...
- Page 4 INFORMATION REAR TRACK SYSTEM INSTALLATION 1. For installation purposes, directional arrows have 1. Using a lifting device, raise the rear of the vehicle been cut out of some components in the anchor and install appropriate stands. Ensure that the bracket kits. These arrows indicate the front of the vehicle is immobilized and safe to work on.
- Page 5 8. Secure anchor bracket to suspension trailing using the provided spacers (B6) and bolts (B5). Torque bolts to 50 N•m [37 lb•ft]. See Fig. 8 Fig. 5 6. Thread hexagonal spacers (B8) on trailing arm bolts. Torque hex spacers to 50 N•m [37 lb•ft]. See Fig.
- Page 6 10.Secure undercarriage to rear hub using the 12.Verify that spring assembly bolt (6) is tightened to provided lug nuts (D). See Fig. 10 the recommended torque specification: 75 N•m [55 lb•ft]. Refer to Fig. 12 CAUTION: If needed, take rubber protector off of hub.
- Page 7 FRONT TRACK SYSTEM 6. Re-attach anti-rotation bracket using its assembly bolts and washers. Tighten bolts to 50 N•m [37 lb•pi] INSTALLATION of torque. Replace anti-rotation arm back into position. See la Fig. 15 1. Using a lifting device, raise the front of the vehicle and install appropriate stands.
- Page 8 8. Remove bolt, washer and bushings from front 9. Remove M10x60mm bolt (C3) from each steering stabilizing rod end and insert bolt in front anchor limiter assembly kit and insert bolt in front anchor bracket (A1-A2) as shown in Fig. 18 bracket (A1-A2) hole shown in Fig.
- Page 9 10.Position bottom part of anchor bracket (A1-A2) assembly under front lower suspension arm, as shown in the figure below. Position bracket cover (A3-A4) over suspension arm and insert tenon, located at the back, in mortise cut in bottom part. Align holes in cover and bottom part. Insert M10x65mm bolts (A5) through bottom and secure the two parts together with nuts (A6) provided.
- Page 10 IMPORTANT STEERING LIMITER ADJUSTMENT WARNING: Before going to the next steps, 15.Apply grease evenly all around step spacer bushing make sure that stabilizing arms are correctly (C5) and in hole of aluminum disk (C1) when installed, and that the angle of attack and assembling these parts together.
- Page 11 18.Reverse steering wheel a little to be able to bolt support plate and cable together. Tighten provided bolt (C4) to 35 N•m [24 lb•ft]. See Fig. 28. Repeat steps on right side. Fig. 28 FINAL INSTALLATION 1. Verify the suspension settings. If the shock absorbers are adjustable, they should be adjusted to the stiffest setting to allow for maximum clearance between the System and the vehicle’s...