Télécharger Imprimer la page

Sony XAV-AX4000 Mode D'emploi page 11

Masquer les pouces Voir aussi pour XAV-AX4000:

Publicité

Les langues disponibles

Les langues disponibles

*1 Not supplied
*2 Speaker impedance: 4 Ω to 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Power amplifier (not supplied)
*5 Subwoofer (not supplied)
*6 Depending on the type of car, use an adaptor for a
steering wheel remote control (not supplied).
For details on using the steering wheel remote control,
see "Using the steering wheel remote control" (page 13).
*7 Depending on the type of car, use an adaptor (not
supplied) if the antenna (aerial) connector does not fit.
*8 Whether in use or not, route the microphone input cord
so it does not interfere with driving operations. Secure
the cord with a clamp, etc., if it is installed around your
feet.
*9 For details on installing the microphone, see "Installing
the microphone" (page 12).
*10 For more information on how to install the SiriusXM
Connect Vehicle Tuner, consult the installation guide
supplied with the tuner.
*11 When connecting the iDataLink Maestro module (not
supplied), do not connect any device to the REMOTE IN
terminal (blue). Likewise, when connecting a device to
the REMOTE IN terminal (blue), do not connect the
iDataLink Maestro module (not supplied) to the IDATA
LINK I/F terminal (black).
*12 Use the connection cable supplied with the iDataLink
Maestro module (not supplied).
*13 Connect when using Apple CarPlay with a wireless
connection.
Making connections
 To a common ground (earth) point
First connect the black ground (earth) lead then
connect the yellow and red power supply leads.
 To the +12 V power terminal which is
energized at all times
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
 To the +12 V power terminal which is
energized when the ignition switch is set to
the accessory position
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
 To the power antenna (aerial) control lead or
the power supply lead of the antenna (aerial)
booster
It is not necessary to connect this lead if there is
no power antenna (aerial) or antenna (aerial)
booster, or with a manually-operated telescopic
antenna (aerial).
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a
power antenna (aerial). Connecting any other
system may damage the unit.
Note
It will take about 10 seconds to shut down the output of
REM OUT after the unit is turned off.
 To a car's illumination signal
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
 To the parking brake switch lead
The mounting position of the parking brake
switch lead depends on your car.
Be sure to connect the parking brake lead (light
green) of the power supply leads  to the
parking brake switch lead.
Parking brake switch lead
Hand brake type
 To the +12 V power terminal of the car's rear
lamp lead (only when connecting the rear
view camera)
 To a car's speed pulse signal
When using Apple CarPlay with a wireless
connection, it is necessary to connect to keep
the accurate location of your car.
The mounting position of the speed pulse
output lead depends on your car.
Rear View Camera Connection
Installation of a rear view camera (not supplied) is
required before use.
Connect a rear view camera power cord (lead) to
the accessory power terminal.
When connecting the iDataLink Maestro module
(not supplied) and you are using the Backup
Camera Dynamic Guidelines function, adjust the
guideline.
 2.0 m (6
1
/
feet) behind the car
2
 0.5 m (1
3
/
feet) behind the car
4
Memory hold connection
When the yellow power supply lead is connected,
power will always be supplied to the memory
circuit even when the ignition switch is turned off.
Foot brake type
11
GB

Publicité

loading