KitchenAid KBSD702MPS Guide De Démarrage Rapide

OPERATING INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY
INSTRUCTIONS, located in your appliance's Owner's Manual, before operating this appliance.
IMPORTANT: Before operating this appliance, make sure it has been properly installed according to the
appliance's Owner's Manual.
The Temperature Control UI is located inside the appliance above the crisper drawers.
For your convenience, your refrigerator and freezer temperature controls are set to the recommended set
points at the factory. When you first install your refrigerator, make sure the temperature controls are still set
to the recommended set points. The recommended set points are 37°F (3°C) for the refrigerator and
0°F (-18°C) for the freezer.
IMPORTANT:
� The recommended settings should be correct for normal household refrigerator use. The controls
are set correctly when milk or juice is as cold as you like and when ice cream is firm.
NOTE: Areas such as a garage, basement, or porch may have higher humidity or extreme
temperatures. You may need to adjust the temperature away from the recommended settings to
accommodate for these conditions.
� When the power is on, the temperature display shows the set point temperature of the compartment.
� Wait 24 hours for your refrigerator to cool completely before adding food. If you add food before the
refrigerator has cooled completely, your food may spoil.
NOTE: Adjusting the refrigerator and freezer controls to a colder than recommended setting will not
cool the compartments any faster.
� If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be
sure they are not blocked before adjusting the controls.
� Wait at least 24 hours between adjustments. Recheck the temperatures before other adjustments
are made.
Turning Refrigerator Cooling On/Off
Your refrigerator and freezer will not cool when cooling is turned off. Follow the directions specific to your
model.
Turn ON
� Press and hold Max Freeze and Max Cool buttons at the same time for 3 seconds.
Cooling Off icon blinks twice and remains on.
Setting the Temperature °F/°C preset at °F
� Press °F - °C button to change between Celsius and Fahrenheit.
When activated, the selected temperature option displays. When deactivated,
the LED is Off.
Adjusting Temperature
The following applies to both the refrigerator temperature button and freezer temperature button.
Pressing the Freezer or Refrigerator picture button once will increase or decrease the temperature
(1°C, 2°F).
Once the temp setting reaches the lowest temperature allowed for that zone, the next button press will
change the temperature to the highest temperature allowed for that zone (looping).
The Refrigerator temperature range will be from 33°F to 42°F (1°C to 6°C), with the factory default
temperature being 37°F (3°C).
The Freezer temperature range will be from -8°F to 5°F (-22°C to -15°C), with the factory default
temperature being 0°F (-18°C).
CONDITION/REASON
REFRIGERATOR too cold
REFRIGERATOR too warm
FREEZER too cold
FREEZER too warm/too little ice
Water Filter Indicator and Reset (all models)
The water filter indicator, located on the control panel, will help you know when to change the water filter.
Replace status:
� When the internal control panel's water filter status displays, this tells you that
it is almost time to change the water filter cartridge. Replace the water filter
cartridge.
Replace Overdue status:
� When the light turns red on the control panel, this tells you that it is time to
change the water filter cartridge.
� It is recommended that you replace the filter when the status light turns red or
water flow to your water dispenser or ice maker decreases noticeably.
NOTE: If water flow to your water dispenser or ice maker decreases noticeably,
change the filter sooner. The filter should be replaced at least every 6 months,
depending on your water quality and usage.
When dispensing water after the Replace Filter icon is on, the Replace Filter icon
blinks for the duration of dispensing. This applies for both the Replace Filter state
and Replace Overdue status. Fourteen days after the Replace Filter indicator
turns On, it shall enter "Replace Overdue" mode.
Filter Reset
After changing the filter, press and hold Filter Reset button for 3 seconds. The button will no longer display
once reset.
See the "Water Filtration System" section in Owner's Manual for steps to remove and replace filter.
W11572271D
W11572272D-SP
Built-in SXS Non-Dispensing Quick Start Guide
TEMPERATURE ADJUSTMENT
REFRIGERATOR Control 1°C or 2°F higher
REFRIGERATOR Control 1°C or 2°F lower
FREEZER Control 1°C or 2°F higher
FREEZER Control 1°C or 2°F lower
Max Cool/Max Freeze
Max Cool
The Max Cool feature assists with periods of high refrigerator use, full grocery loads, or
temporarily warm room temperature.
� Press Max Cool to set the freezer and refrigerator to the lowest temperature settings.
Press Max Cool again to return to the normal refrigerator set point.
NOTE: The Max Cool feature will shut off automatically in approximately 12 hours.
� While Max Cool is ON, changing the refrigerator temperature will deactivate Max Cool.
� While Max Cool is ON, activating Vacation Mode will deactivate Max Cool.
Max Freeze
The Max Freeze feature assists with temporary periods of heavy ice use by increasing ice
production.
� Press Max Freeze to set the freezer to the lowest temperature setting.
Press the Max Freeze feature touch pad again to return to the normal freezer set point.
� While Max Freeze is ON, changing the freezer temperature will deactivate Max
Freeze.
NOTE: The Max Freeze feature will shut off automatically in approximately 48 hours.
Alarm Functions
Door Open
The Door Ajar Alarm feature sounds an alarm when the refrigerator or freezer door is open
for 5 minutes and the product cooling is turned on. The alarm will repeat every 2 minutes.
Close both doors to turn it off. The feature then resets and will reactivate when either door
is left open again for 5 minutes.
Power Outage
The power outage indicator lets you know if the power supply to the refrigerator has been cut off and the
freezer temperature has risen to 18°F (-8°C) or higher. When power has been restored, the button
repeatedly flashes and the red Power Outage icon appears. When the indicator is on, all other control and
dispenser functions are disabled until you confirm that you are aware of the power outage.
� Press any button to reset the display screen to its normal status.
Miscellaneous
Crisper Menu
There are 4 preset temperatures for the Crisper Menu. Press the crisper menu button to select the desired
option. Coldest to Warmest - Meats, Deli, Assorted, Produce.
� MEAT setting is coldest setting and can be used for defrosting frozen items that need defrosting in the
refrigerator.
� PRODUCE setting is warmest setting and used for everyday vegetables and fruits.
� ASSORTED setting is used to keep different items in the same drawer.
� DELI setting is used for Deli meats and cheeses or non produce items.
Control Lock
Press and hold [Crisper] button and the Lock indicator will blink twice, play a tone and remain on/off.
When Control Lock is active;
� All other functions are not accessible.
� Pressing any button will play invalid tone 3 times and lock indicator blinks 3 times.
� Water/Ice paddles are not available, pressing the paddles will play invalid tone 3 times.
Showroom Mode
Demo mode for sales floor. Press and Hold the [RC Temp] + [FC Temp] buttons for 5 seconds, the
showroom indicator will blink twice to remain on/off.
Online Ordering Information
For detailed installation instruction and maintenance information, winter storage, and transportation tips,
please see the Owner's Manual included with your appliance.
For information on any of the following items, the full cycle guide, warranty, detailed product dimensions, or
for complete instructions for use and installation, please visit
https://www.kitchenaid.com/service-and-support, or in Canada
https://www.kitchenaid.ca/service-and-support. This may save you the cost of a service call. However,
if you need to contact us, use the information listed below for the appropriate region.
To purchase additional bakeware please visit: https://www.kitchenaid.com/kitchenware/bakeware
United States:
1–800–422–1230
KitchenAid Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022–2692
Get Started with your built-in refrigerator.
Scan to see top features, tips and how-to videos.
SAVE THESE INSTRUCTIONS
Canada:
1–800–807–6777
KitchenAid Brand Home Appliances
Customer eXperience Centre
200–6750 Century Ave.
Mississauga, Ontario L5N 0B7