Hoover Candy Manuel D'utilisation page 12

8. Pull the plunger of the Food saver tool completely. [Fig. 3-14]
9. Turn on the product keeping the red component on the air valve with your hand. [Fig. 3-14] Once the vacuum is turned
on, you will see the bag begin to shrink as air is removed. When the bag stops shrinking, it means you have completed
the sealing process. At this point you can turn off the product.
10. Remove the Food Saver tool and close the air valve, pressing it with your fingers several times to prevent any air from
escaping the bag. [Fig. 3-14]
11. Store it in the fridge or freezer.
How to use the Space Saver kit*:
1. Insert the kit connector into the product inlet.
2. Insert the Space Saver tool (in light blue colour) into the kit connector. [Fig. 3-15]
3. Take the vacuum bag for of soft goods/cloths open it grabbing each side of the zipper and pulling the side apart.
4. Put the soft goods inside the bag, placing the open bag face-up on a flat surface. The air valve must be facing
upwards. [Fig. 3-16] Be sure not to overfill the bag. Make sure that all items are dry before packing them.
5. Take one sure-zip (included in the kit) and put it on the top of your vacuum bag to help you sealing it. Firmly grasp the
sure-zip slider using your thumb and index fingers. Then, slide the zipper across the top of the bag. Make sure to slide
the zipper back and forth at least twice. Press down a little harder to ensure a tight seal has been made, and no air will
leak out. [Fig. 3-16]
6. Run your fingers along the zipper. To ensure that the zipper is completely sealed, slide your fingers along the zipper
track and press down. You should be able to feel if any areas are not sealed.
7. Open the valve cap on the top of the bag. [Fig. 3-17] To open the valve cap, place one hand around the base of the
valve and use the other to rotate and lift the cap.
8. Place the circular light blue component of the Space Saver kit onto the air valve. Make sure to cover the air valve
completely with this light blue component. [Fig. 3-17]
9. Turn on the product. Once the vacuum is turned on, you will see the bag begin to shrink as air is removed. When the bag
stops shrinking, it means you have completed the sealing process. At this point you can turn off the product. [Fig. 3-17]
10. Remove the Space Saver tool and close the air valve, putting back the valve cap and rotating it to prevent any air from
escaping the bag. [Fig. 3-17]
11. Store it on a smooth and flat surface. Make sure there are no sharp objects placed near the bag.
CLEANER MAINTENANCE [Fig. 4]
Emptying the Dust Bin
1. Press the bin release button and remove the dust bin. [Fig. 4-3]
2. Pull the metal ring and remove the pre-motor filter pack (metal mesh and pre-motor filter). [Fig. 4-4]
3. Empty the debris from the dust bin. [Fig. 4-5]
4. Remove excess debris from the metal mesh then hold the base of the metal mesh and rotate the top in an anticlockwise
direction and remove the pre-motor filter. [Fig. 4-6]
5. Tap the base and the top of the pre motor filter to remove dust, then using the dusting brush remove any additional
debris from the pre-motor filter and metal mesh. [Fig. 4-7]
6. Once all excess dust and debris is removed, wash the pre-motor filter and metal mesh with warm water until the water
runs clean. Do not wash the DUST BIN as there are electronic parts inside the dust bin. [Fig. 4-8]
7. Remove excess water and leave to dry for 24 hours. Only refit the filter and mesh when completely dry. [Fig. 4-9]
8. Reassemble once completely dry and refit to the product. [ Fig. 4-11]
NOTE: Do not use hot water or detergent when cleaning the pre-motor filter. In the unlikely event of the pre-motor
becoming damaged, fit only a genuine Hoover replacement part. Please ensure you Re-Fit the pre-motor filter into the
dust bin as the product is fitted with a filter protection mechanism which will prevent the dust bin being reassembled to
the product.
IMPORTANT: For optimum performance , always keep your filter clean. We recommend that you wash your pre-motor
filter and mesh at least once per month.
WARNING: DO NOT WASH THE DUST BIN as there are electronic parts inside. You can clean the dust bin with
a dry cloth.
CLEARING AN ACCESSORY BLOCKAGE [Fig. 5]
If the product works with the attached accessory and the on/off LED is blinking in red color with the flashing frequency of
2HZ, it informs the attached accessory is blocked and so you need to check and remove the blockage from the accessory
or/and from the product inlet or bin.
IMPORTANT: Always switch the cleaner off and remove all the accessories from the cleaner before attempting any
maintenance.
5
GB