Fein WSG7-100 Serie Manuel D'utilisation page 20

OBJ_BUCH-0000000388-001.book Page 20 Monday, May 27, 2019 1:40 PM
en
20
An estimation of the level of exposure to vibration
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the expo-
sure level over the total working period.
Identify additional safety measures to protect the oper-
ator from the effects of vibration such as: maintain the
tool and the accessories, keep the hands warm, organi-
sation of work patterns.
Handling hazardous dusts
For work procedures with this power tool where
material is removed, dusts develop that can be hazard-
ous to one's health.
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate parti-
cles from materials containing stone, paint solvents,
wood preservatives, antifouling paints for vessels, can
trigger allergic reactions to the operator or bystanders
and/or lead to respiratory infections, cancer, birth
defects or other reproductive harm. The risk from
inhaling dusts depends on the exposition. Use dust
extraction matched appropriately for the developing
dust, as well as personal protective equipment and pro-
vide for good ventilation of the workplace. Leave the
processing of asbestos-containing materials to special-
ists.
Wood and light-metal dust, hot mixtures of grinding
dust and chemical materials can self-ignite under unfa-
vourable conditions or cause an explosion. Avoid
sparking in the direction of the dust collector as well as
overheating of the power tool and the materials being
sanded, empty the dust collector/container in time,
observe the material manufacturer's working instruc-
tions, as well as the relevant regulations in your country
for the materials being worked.
Operating Instructions.
The self-start lock prevents the angle grinder (see
Table) from automatically restarting again, even after a
brief interruption of the power supply, e. g., from a
pulled mains plug.
In this case, switch the power tool off, remove it from
the work piece and check the application tool. After-
wards, switch the power tool on again.
Angle grinder with self-start lock (see Table).
WSG7-115 (**)
Angle grinder with self-start lock and electronics (see
Table) are equipped with overload and blocking protec-
tion. In case of overload or blocking of the application
tool, the power supply is interrupted. In this case,
switch the power tool off, remove it from the work-
piece and check the application tool. Afterwards, switch
the power tool on again.
WSG7-125 (**)
Press the locking button only when the motor is
stopped (see page 5).
Turning the machine head:
Carefully turn the machine head to the new position
without removing it from the housing.
Repair and customer service.
tool. The total insulation of the power tool can be
impaired. Blow out the interior of the power tool via
the ventilation slots frequently with dry and oil-free
compressed air, and connect a residual current device
(RCD) on the line side.
If the supply cord of this power tool is damaged, it must
be replaced by a specially prepared cord available
through the FEIN customer service centre.
Products that have come into contact with asbestos
may not be sent in for repair. Dispose of products con-
taminated with asbestos according to the applicable
country-specific regulations for such disposal.
The current spares parts list for this power tool can be
found on our website at www.fein.com.
Use only original spare parts.
If required, you can change the following parts your-
self:
application tools, auxiliary handle, clamping flanges,
wheel guard
Warranty and liability.
The warranty for the product is valid in accordance
with the legal regulations in the country where it is mar-
keted. In addition, FEIN also provides a guarantee in
accordance with the FEIN manufacturer's warranty dec-
laration.
The delivery scope of your power tool may include
only a part of the accessories described or shown in this
Instruction Manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the
last page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH,
D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories
should be sorted for environmental-friendly recycling.
7 221 98 ...
Selection of accessories (see page 9).
Use only original FEIN accessories. The accessories
must be intended for the power tool type.
A Grinding disc, flap disc
B Cutting disc
C Steel wire brush
7 222 65 ...
When working metal under extreme oper-
ating conditions, it is possible for conductive
dust to settle in the interior of the power
(use only with mounted wheel guard)
(use only with mounted cut-off wheel guard)