Télécharger Imprimer la page

Sunrise Medical Quickie Q300 M Mini Manuel D'utilisation page 30

Masquer les pouces Voir aussi pour Quickie Q300 M Mini:

Publicité

Les langues disponibles

Les langues disponibles

9. Attach the five screws together with the plastic spacer/
spacers (to prevent the batteries from coming into contact
with the nuts) and the lock plate on the underside of the
chassis box. Tightening torque: 16-18 Nm/13.3 lb.ft (Fig. 7.14).
Please refer to Section 6.6 of this manual for reverse the
procedure to replace batteries.
10. Perform final check by connecting the wheelchair to the
docking station. Check that it is securely locked and make sure
that all release methods work as intended (Fig. 7.15).
A warning tone will sound if the lock plate is not properly
engaged.
(A) Release button.
(B) Manual operating lever.
(C) Emergency release.
(D) Red LED.
(E) Green LED.
(F) Lock Plate.
(G) Lock Pin.
Securing the wheelchair in the docking station:
Make sure that the leg rests are not colliding with the ramp or
the docking station when entering the vehicle.
1. Manoeuvre the wheelchair slowly and in a uniform direction
over the docking station. The lock plate under the wheelchair
helps to guide the wheelchair into place in the docking station.
When the lock plate is fully engaged in the docking station, a
spring-action locking pin automatically secures the lock plate.
2. The docking station is equipped with a control switch that
indicates whether the lock plate is correctly secured in the
docking station. As soon as the lock plate comes into contact
with the locking pin, a warning tone will sound (a high-pitched
howl), and the red diode/lamp (LED) in the control panel will
light up until the lock plate is either fully engaged or else the
wheelchair is removed from the docking station.
3. As an indication that the wheelchair is properly secured, the
warning tone will cease, the red diode in the control panel will
go out and the green diode lamp (LED) will light up.
4. Do not forget to buckle up for driving.
Release from the docking station
1. When the vehicle has been brought to a halt, remove the
safety belt.
2. To unlock commence by driving the wheelchair forward to
release pressure on the lock pin and then press the red release
button in the control panel. The locking pin will be triggered/
released for approx. 5 seconds, after which the locking pin
is automatically locked/activated again. Do not attempt to
reverse out of the docking station until the red LED on the
control module, which indicates the unlock position, has been
illuminated.
30
F
F
WARNING! Attempting to reverse the wheelchair before
the red LED has been illuminated will result in blocking the
docking stations lock mechanism, which makes it impossible to
reverse. If this happens repeat above unlocking procedure.
3. Move the wheelchair away from the docking station within
this 5-second period.
Manual release in case of electrical failure
1. In the event of electrical failure, a manual emergency release
is located at the front edge of the docking station. Move
wheelchair forward to release pressure on the lock pin and
push the red release arm to one side and hold it there while
the wheelchair reverses out of the docking station.
2. A cable-activated manual operating lever can also be fitted
(accessory). The red release arm must pushed to one side and
should be held there whilst the wheelchair moves away.
3. If the described manual release procedures fails, an
emergency release tool made from red plastic comes with
each docking station.
Move wheelchair forward to release pressure on the lock pin and
place the emergency release tool in the gap between the locking
plate and the docking station. Push the release tool forward
until the locking pin will has been forced down - after which the
wheelchair can be reversed out of the docking station.
Please also refer to Dahl Engineering instructions for
Installation, Use and Maintenance
Fig. 7.14
Fig. 7.15
D
E
A
B
C
Q300 M Mini Rev.F

Publicité

loading