Bosch GOP 18V-28 Professional Notice Originale page 7

An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for sawing and cutting wood-
based materials, plastic, plasterboard, non-ferrous metals
and mounting elements (e.g. non-hardened nails, clamps). It
is also suitable for working on soft wall tiles and for dry sand-
ing and scraping of small areas. It is ideal for working close to
edges and flush with surfaces. The power tool must only be
operated using Bosch accessories.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) On/off switch
(2) Ventilation slots
A)
(3) Battery
(4) Orbital stroke rate preselection thumbwheel
(5) SDS lever for unlocking tools
(6) Tool holder
(7) Worklight
A)
(8) Battery release button
(9) Clamping lever for depth stop
A)
(10) Depth stop
A)
(11) Plunge cut saw blade
(12) Handle (insulated gripping surface)
A)
(13) Dust extraction system
A)
(14) Sanding plate
A)
(15) Sanding sheet
(16) Clamping lever for dust extraction system
A)
(17) Dust extraction outlet
A)
(18) Dust extraction adapter
Bosch Power Tools
(19) Dust extraction hose
A) Accessories shown or described are not included with the
Technical data
Cordless multi-cutter
Article number
Rated voltage
No-load speed n
Oscillation angle on left/right
Weight according to
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
ure during operation
during storage
Recommended rechargeable
batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
Technical data determined using the battery that comes with the
product.
Fitting
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Battery Charging
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
A) full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
A)
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
The battery (3) is equipped with two locking levels to pre-
vent the battery from falling out if the battery release button
A)
product as standard. You can find the complete selection of
accessories in our accessories range.
min
0
B)
and
1 609 92A 5NN | (05.06.2020)
English | 7
GOP 18V-28
3 601 HB6 0..
V= 18
-1
8000–20000
° 1.4
A)
kg 1.5–2.6
°C 0 to +35
°C −20 to +50
GBA 18V...
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...