Nolan N21 VISOR Sécurité Et Instructions D'utilisation page 7

N21 VISOR
VISOR (NJS-09)
1 VISOR DISASSEMBLY
1.1 Close the visor and remove the side plate from the helmet by pulling the upper end
outwards (Fig.1).
1.2 Push the visor mechanism slider forwards as shown by the arrow (Fig.2).
1.3 Lift the rear area of the visor from the shell until it is completely released from the
mechanism; slightly push it towards the front of the helmet (Fig.3).
1.4 Repeat all the operations on the other side as well.
2 VISOR ASSEMBLY
2.1 Place the visor on the shell taking care to align the teeth seat with the front part
of the mechanism; hook the visor under the mechanism by pressing it against the
helmet in the teeth area and simultaneously pushing it towards the rear part of the
helmet so as to completely hook it to the mechanism (Fig.3).
2.2 Move the slider backwards until you hear the fastening click (Fig.2).
2.3 Assemble the side plate taking care to center the internal hooks in the relative
seats on the mechanism and pressing until you hear the fastening click (Fig.4).
2.4 Repeat the operations on the other side as well.
the left and right side plates are different from each other and are marked on
their back as R (Right) and L (Left).
WARNING
- Make sure that the mechanisms are working properly. Open and close the visor
making sure that the mechanisms hold it in the different positions.
If necessary, repeat the above-mentioned steps.
- Do not use the helmet if the visor and the side plates have not been assembled
properly.
- Do not remove the side mechanisms from the shell.
- Should any of the side mechanisms fail or be damaged, please refer to a
Nolangroup authorized dealer.
SIDE PLATES FRAMES
The side plates are equipped with a colored frame that can be removed.
1 SIDE PLATES FRAME DISASSEMBLY
To remove the frame from a side plate first remove the side plate from the helmet (see
instructions above).
1.1 Pull the front part of the frame forward (and then inward), slightly deforming it, to
release the plate front grip pawl A1 from its seat B1 on the frame (Fig.5).
1.2 Push back the frame to release its three back fastenings C1, C2 and C3 from their
seats D1, D2 and D3 on the side plate (Fig.6) and finally disconnect the frame and
the plate.
the left and right side plates frames are different from each other and are
marked on their back as R (Right) and L (Left).
12
INSTRUCTIONS FOR USE
2 SIDE PLATES FRAME ASSEMBLY
2.1 Insert the right or left side plate front part on the relevant left of right frame so as
the plate front grip pawl A1 overlaps its seat B1 on the frame.
2.2 Hook the frame back fastenings C1, C2 and C3 one by one to their seats D1, D2
e D3 on the side plate slightly deforming the frame (Fig.6).
2.3 Hook the side plate grip pawl A1 to its seat B1 on the frame slightly deforming it (Fig.5).
2.4 Make sure that the two components are correctly attached to each other. Then
reassemble the side plate on the helmet (see instructions above)
WARNING
- Make sure that the mechanisms are working properly. Open and close the visor,
making sure that the side plates and the frames hold their positions. If necessary,
repeat the above-mentioned steps.
- Do not use the helmet if the visor and/or the side plates and/or their frames have
not been assembled properly.
- If the side plates and/or the frames and/or the side mechanisms are damaged or
malfunctioning, refer to a Nolangroup authorized dealer..
VISION PROTECTION SYSTEM (VPS) (VPS-13)
The exclusive inner VISION PROTECTION SYSTEM (VPS) is a LEXAN™ (*) - polycar-
bonate moulded sunscreen with scratch-resistant treatment. Using it is very simple and
practical: Just lower it to activate it or lift it to remove it from the field of vision. It is
useful in all sorts of situations, both on long journeys out of town and shorter town trips.
1 VPS OPERATION
The VPS mechanism allows activating the sun screen by simply lowering it until it par-
tially covers the visor field of vision. In this way, the desired light transmittance reduc-
tion is achieved. At any time, without operating the visor, the VPS can be deactivated
with a simple movement and easily lifted up to restore the normal conditions of visibility
and protection guaranteed by the approved helmet visor.
1.1 To deactivate the VPS, push the side slider completely downwards (Fig.7A).
1.2 To activate the VPS, push the side slider completely upwards (Fig.7B).
2 PRECAUTIONS FOR USE
Current homologation standards (ECE22-06) establish that the minimum light trans-
mittance levels of visors must be no less than 80%; for homologated sunscreens, the
minimum transmittance level must be no less than 20%.
The regulation itself also contemplates the simultaneous use of the visor and sun-
screen, both as standard.
WARNING
- We recommend your using of the VPS only and solely together with the approved
standard visor, which has a transmittance value greater than 80%.
- The VPS does not replace the protection guaranteed by the visor.
- The VPS can only be activated during daytime and in weather and environmental
di conditions with a particular light, for example, strong brightness caused by high
(*) LEXAN is a trademark of SABIC.
N21 VISOR
13
INSTRUCTIONS FOR USE