Numark HDMIX Guide D'utilisation page 13

3. CHANNEL 2 – This channel is routed to the left side of the crossfader and features the following
controls:
LINE / DECK A – Selects the input source to be routed to this mixer channel. Select LINE if you
would like to route an external line-level input source, such as a CD player, to this channel.
Select DECK A if you would like to route virtual deck A to this channel (tracks can be sent to the
virtual deck via the menus on the screen).
TRIM – Adjusts the channel's pre-fader gain level ± 10dB.
TREBLE – Adjusts the high (treble) frequencies of the channel ± 10dB.
MID – Adjusts the mid-range frequencies of the channel ± 10dB.
BASS – Adjusts the low (bass) frequencies of the channel ± 10dB.
VOLUME FADER – Adjusts channel volume.
CUE – Sends the Channel 1 signal to the Headphone channel for cueing.
4. CHANNEL 3 – This channel is routed to the right side of the crossfader and features the following
controls.
LINE / DECK B – Selects the input source to be routed to this mixer channel. Select LINE if you
would like to route an external input source, such as a CD player or turntable (if using a phono-
line turntable, plese make sure that the Channel 3 LINE / PHONO switch is set to PHONO).
Select DECK B if you would like to route the virtual deck to this channel (tracks can be sent to the
virtual deck via the menus on the screen).
TRIM – Adjusts the channel's pre-fader gain level ± 10dB.
TREBLE – Adjusts the high (treble) frequencies of the channel ± 10dB.
MID – Adjusts the mid-range frequencies of the channel ± 10dB.
BASS – Adjusts the low (bass) frequencies of the channel ± 10dB.
VOLUME FADER – Adjusts channel volume.
CUE – Sends the Channel 1 signal to the Headphone channel for cueing.
5. MASTER CHANNEL – This channel controls the Master and Zone outputs.
BALANCE – Adjusts the Master mix in the left-right panorama. As the knob is moved to the right,
the left side of the signal is attenuated and vice versa.
ZONE – Adjusts the level of the Zone output. The Zone output is most often connected to audio
recorders or additional speaker systems for monitoring your mix. The Zone knob allows you to
set the audio level sent to these devices, independently of the Master output audio levels.
MASTER – Adjusts the level of the Master output.
MONO – Mixes the Master stereo mix to mono. This is useful when connecting the HDMIX to
power amplifiers or speaker systems which require a mono input.
6. HEADPHONE CUE CONTROLS – These controls affect the signal in the Headphone channel:
SPLIT – "Splits" the headphone audio such that all channels sent to CUE are mixed to mono and
applied to the left headphone output and the Master output is mixed to mono and applied to the
right channel.
CUE TONE – Adjusts the tone of the Headphone output. Turn the knob to the left to accentuate
low (bass) frequencies or turn the knob to the right to accentuate high (treble) frequencies.
CUE GAIN – Adjusts the level of the Headphone output.
CUE MIX – Crossfades between CUE and MASTER. Please note that this will only have an
effect while SPLIT is disabled.
7. CROSSFADER CONTROLS:
CROSSFADER – Blends audio between Channels 2 & 3. In the right-most position, you will hear
only audio present on Channel 2.
simultaneously. In the left-most position, you will hear only audio present on Channel 3.
CROSSFADER ON / OFF – This switch turn the crossfader on and off. When the crossfader is
turned off, Channels 2 & 3 will be sent directly to the Master mix and crossfader position will have
no effect.
In center position, you will hear Channels 2 & 3
13