Disposing Of Packaging; Connecting The Appliance; Switching On The Appliance; Control - Atag KD8178BD Instructions D'utilisation Et De Montage

The door stop cushioning can be
adjusted if necessary using the
accompanying Allen key:
u For stronger spring force: turn
clockwise.
u For lesser spring force (as-deliv-
ered): turn anticlockwise.
u Attach the remaining covers to
the hinges.
Check the following points to ensure the appliance is fitted
properly. Failure to do so may lead to icing, condensate
forming and malfunction:
w The door has to close properly
w The unit door must not butt against the unit body
w The seal must have a firm fit at the upper corner on the
handle side. To check, darken the room, place a torch inside
the appliance at the top and close the door. If light shines
through, check the assembly.

4.5 Disposing of packaging

WARNING
Danger of suffocation due to packing material and plastic film!
u Do not allow children to play with packing material.
The packaging is made of recyclable materials:
corrugated board/cardboard
-
- expanded polystyrene parts
- polythene bags and sheets
polypropylene straps
-
nailed wooden frame with polyethylene panel*
-
u Take the packaging material to an official collecting point.

4.6 Connecting the appliance

NOTICE
Risk of damage to the electronic control system!
u Do not use stand-alone inverters (conversion of d.c. to a.c./
three-phase) or energy saving plugs.
WARNING
Fire and overheating hazard!
u Do not use extension cables or multiple socket outlets.
The type of current (alternating current) and voltage at the
installation site have to conform with the data on the type plate
(see Appliance at a glance).
Connect the appliance only with a properly installed
socket outlet with earthing contact. The socket outlet
must be fused with 10 A or higher.
It must be easily accessible so that the appliance can
be quickly disconnected from the supply in an emer-
gency. It must be outside the area of the rear of the
appliance.
u Check the electrical connection.
u Plug in the power plug.

4.7 Switching on the appliance

Note
u To switch on the entire appliance it is necessary only to
switch on the freezer compartment.
Put the appliance into operation about 2 hours before first
loading food to be frozen.
Do not load food to be frozen before the temperature display
reads -18 °C.
4.7.1 Switching on the freezer compartment
u Press On/Off button, freezer compartment
w The refrigerator compartment temperature display shows
the set temperature.
w The temperature display of the freezer compartment flashes
until the temperature is sufficiently low. If the temperature is
above 0 °C, dashes flash. If it is below, the set temperature
flashes.
4.7.2 Switching on the refrigerator compart-
ment
u Press On/Off button, refrigerator compartment
w The interior light is on when the door is open.
w The temperature display shines. The refrigerator compart-
ment is switched on.

5 Control

5.1 Brightness of the temperature
display
You can adjust the brightness of the temperature display to the
light conditions of the room in which the appliance is installed.
5.1.1 Adjusting the brightness
The brightness can be adjusted between h1 (minimum lumi-
nance) and h5 (maximum luminance).
u To activate the setting mode: Press the Fast Freeze button
Fig. 2 (2) for about 5 seconds.
w The Fast Freeze button flashes. The display indicates c.
u Using the "+" setting button, freezer compartment
and "-" setting button, freezer compartment
h.
u To confirm: Briefly press the Fast Freeze button
u To make the display brighter: Press the "+" setting
button, freezer compartment
u To make the display darker: Press the "-" setting
button, freezer compartment
u To confirm: Press the Fast Freeze button
Fig. 2 (2) .
w The brightness is adjusted to the new value.
u To deactivate the setting mode: Press the On/Off button,
Fig. 2 (3) .
freezer compartment
-or-
u Wait for 5 minutes.
w The temperature is indicated again in the temperature
display.

5.2 Child proofing

The child-proofing function enables you to make sure that the
appliance is not inadvertently switched off by playing children.
5.2.1 Setting the child lock
u To activate the setting mode: Press the Fast Freeze button
Fig. 2 (2) for about 5 seconds.
Control
Fig. 2 (3) .
Fig. 2 (11) .
Fig. 2 (5)
Fig. 2 (4) , select
Fig. 2 (2) .
Fig. 2 (5) .
Fig. 2 (4) .
35