Publicité
Les langues disponibles
Les langues disponibles
installation
Contact your local building inspector prior to installa-
tion. A permit may be required in your area.
1. Remove all parts from inside the stove body.
2. Select the proper location for the stove. These appli-
ances must not be installed any closer than the mini-
mum clearance to combustible materials. shown in
Brick pattern (on diagram sheet). The stove must be
installed on a noncombustible surface as shown in
Figure 1.
Figure 1
Clearance from Combustible Materials
Back Wall
B
8"
A
D
8"
8"
clearance to combustible Materials
A minimum clearance of 18" (457 mm) to the chimney connector may be
required by the authority having jurisdiction.
ST1005
from Heater
CDW244
A. Sidewall
17Z\x" (445 mm) D. Sidewall
clearances
B. Back Wall
13" (330 mm)
9/08
C. Corner
11" (279 mm)
Minimum height to ceiling
* 16" (406 mm) US
Unit must be placed on a noncombustible floor protection
equivalent to 3/8" millboard. Floor protector must have min.
R value of .893. Consult your local building authorities for fur-
ther information.
3. If noncombustible materials have been installed on the
walls, obtain the minimum clearances from either the
manufacturer of these materials or the local building
inspector's office.
4. Install the refractory bricks. (Fig. 2) (Refer also to Page
10) Be sure all bricks are in place.
5. Install the stovepipe INSIDE the flue collar on the top
of the stove between the stove and chimney.
6. dO NOt use a grate to elevate the fire.
Stove pipe
1. A clearance of 18" (457 mm) between the stovepipe
and combustible materials may be required. Check
with authorities having jurisdiction in your area.
2. All pipe sections must be connected with the male end
(crimped end) toward the stove.
30005126
All manuals and user guides at all-guides.com
Back Wall
C
E
*16"
**18"
C
F
from chimney connector
28" (711 mm)
E. Back Wall
15Z\x" (394 mm)
F. Corner
22" (559 mm)
54Z\x" (1384 mm)
** 18" (457 mm) Canada
Windsor High Efficiency Wood Stove
2 Full
Figure 2
Bricks
Brick Placement
ST1006
Be sure to install two (2) full
bricks (S16040) in baffle
3. Fasten the stove pipe to the flue collar by the
F
use of three (3) sheet metal screws. Do the same
at each additional joint to make the entire instal-
lation rigid.
4. Maintain the required diameter flue for the en-
tire installation.
5. If you are connecting the stove to an old ma-
sonry flue, be sure to have it inspected for cracks
and general condition.
6. It is recommended that no more than two (2) 90° bends
be used in the stove pipe installation. More than two
(2) 90° bends may decrease the amount of draw and
possibly cause smoke spillage.
7. A damper is not required in this installation. Remove
damper plate in the chimney or secure in the OPEN
position.
8. Single wall flue pipe assemblies must not exceed 10
feet (3 m) in overall length.
cautiON: dO NOt open fire-door to a point where it
would be in contact with the combustible sidewall.
Optional fan - An optional heat exchange blower is avail-
able for this wood burning appliance. To order please see
the local dealer where you purchased your appliance.
proposition 65 Warning: Fuels used in gas, woodburn-
ing or oil fired appliances, and the products of combus-
tion of such fuels, contain chemicals known to the State
of California to cause cancer, birth defects and other
reproductive harm.
California Health & Safety Code Sec. 25249.6
Baffle Assembly
3
Publicité
