DeWalt D24000 Manuel D'instructions page 37

• Do not operate this machine without guards in place.
• Hold the workpiece firmly against the fence and guide during the
cutting operation. Do not perform any operation freehand.
• Do not cut workpieces requiring a maximum depth of cut exceeding
that of the cutting disc.
• Do not perform dry cuts. Dry cutting not only results in damage to the
machine, it will also increase exposure to harmful airborne dust.
• Do not use cutting discs for side grinding.
• Do not cut metal materials.
• Always store cutting discs well-protected and in a dry place, out of
reach of children.
• Do not make adjustments or parts substitutions to alter the factory
settings. Technical alterations should only be carried out by the
manufacturer, in compliance with the applicable safety requirements.
Do not unplug the machine from the mains supply if the mains
plug becomes wet! Disconnect the fuse or circuit breaker of
the mains supply first, only then unplug the machine.
Examine the connections for the presence of water. Take care
that the connections are dry before activating the circuit and
plugging in the machine.
Residual risks
The following risks are inherent to the use of these machines:
– injuries caused by touching the rotating parts
– injuries caused by disruption of the cutting disc
These risks are most evident:
– within the range of operation
– within the range of the rotating machine parts
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be avoided.
These are:
– Impairment of hearing.
– Risk of accidents caused by the uncovered parts of the rotating cutting
disc.
– Risk of injury when changing the disc.
– Risk of squeezing fingers when opening the guards.
Labels on tool
The following pictographs are shown on the tool:
Read the instruction manual before use.
Do not use recessed cutting discs.
Wear safety goggles.
Always wear regular working gloves while operating this tool.
Always wear ear protection.
Warning! Sharp edges.
On/off switch: position I (on) and 0 (off).
Do not place your hands within this area.
All manuals and user guides at all-guides.com
Package contents
The package contains:
1 Motor frame assembly
1 Support frame assembly
1 Water basin
1 Water pump
1 Cutting disc
1 Sliding table
1 Extension table
1 Edge guide
1 Rear water collector
1 Sliding table water collector
4 Allen screws
1 Allen key
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
• Take the time to thoroughly read and understand this manual prior to
Description (fig. A)
Your D24000 tile saw has been designed for professional wet tile cutting
applications. Using the appropriate cutting disc, it can cut concrete, brick,
porcelain and ceramic materials. Providing optimum versatility, the machine
performs the cutting operations of straight cutting (ripping), diagonal
cutting, plunge cutting and bevel cutting easily, accurately and safely.
This machine is not to be used for any operation other than those
mentioned in this manual.
1 On/off switch
2 Depth adjustment knob
3 Operating handle
4 Sliding table
5 Edge guide
6 Extension table
7 Water nozzles
8 Cutting disc
9 Guard
10 Depth stop
11 Bevel adjustment knob
12 Key storage
13 Water basin
14 Sliding table water collector
15 Rear water collector
Electrical safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Mains plug replacement
(U.K. & Ireland only)
• Should your mains plug need replacing and you are competent to do
• Disconnect the plug from the supply.
• Cut off the plug and dispose of it safely; a plug with bared copper
• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly
• The cable wire colours, or a letter, will be marked at the connection
occurred during transport.
operation.
this, proceed as instructed below. If you are in doubt, contact an
authorized D WALT repair agent or a qualified electrician.
E
conductors is dangerous if engaged in a live socket outlet.
rated fuse (1).
points of most good quality plugs. Attach the wires to their respective
points in the plug (see below). Brown is for Live (L) (2), blue is for
Neutral (N) (4) and green/yellow is for Earth (E).
E N G L I S H
37