Dräger X-plore 8000 Notice D'utilisation page 11

6.2 Cleaning and disinfecting
CAUTION
Health hazard
The undiluted agents are damaging to health if they come into
direct contact with the eyes or skin.
► Wear goggles and protective gloves when working with
these agents.
NOTICE
Potential damage to components
► For cleaning and disinfecting only apply the described
procedures and use the specified cleaning agents and
disinfectants. Other agents and procedures, dosages and
exposure times can damage component parts.
For information on suitable cleaning agents and disin-
fectants and their specifications, see document
9100081 at www.draeger.com/IFU.
6.2.1 Cleaning and disinfecting the device
1. Dismantling the device:
a. Separate breathing hose, facepiece and blower unit
from each other.
b. Disconnect the carrying system from the blower unit.
c. If available, dismantle any accessories (e.g. hose and
device sleeves).
d. Dismantle the splash guard cover and respiratory filter
(see "Replacing the respiratory filter", page 12).
2. Clean the facepiece according to the appropriate
Instructions for Use.
3. Cleaning the breathing hose and carrying system:
a. Prepare a cleaning solution containing water and a
cleaning agent.
b. Clean all parts with the cleaning solution using a soft
cloth.
c. Rinse all parts thoroughly under running water.
d. Prepare a disinfectant bath of water and a disinfecting
agent.
e. Place all parts to be disinfected into the disinfectant
bath.
f. Rinse all parts thoroughly under running water.
g. Allow all parts to air-dry or dry them in the drying
cabinet (temperature: max. 60 °C). Keep away from
direct sunlight.
4. Clean and disinfect blower unit and splash guard cover
using disinfectant cloths.
In cases of strong contamination, the blower unit can be
rinsed under running water as follows.
1. Make sure the rechargeable battery remains inserted.
Water must not enter the battery compartment.
2. Close suction inlet and tube connection with plug
(available as accessories).
Instructions for use |
Dräger X-plore
®
8000
6.3 Maintenance work
6.3.1 Visual inspection
Check all parts thoroughly and replace damaged parts if
necessary. In particular, check the respiratory filter sealing
surface and O-rings of the blower unit for damage (e.g.
scratches) or contamination.
6.3.2 Replacing or charging the rechargeable
battery
WARNING
Explosion, fire or chemical hazard!
► Do not remove, insert or charge rechargeable batteries in
potentially explosive or flammable environments.
► Keep rechargeable batteries away from sources of heat.
► Do not short-circuit the rechargeable battery contacts.
► Only use recommended rechargeable batteries.
Removing the rechargeable battery:
1. Fold up carrying system if necessary.
2. Push battery lock button. Ensure that the rechargeable
battery does not fall down.
3. Remove rechargeable battery.
Inserting the rechargeable battery:
1. Fold up carrying system if necessary.
2. Position the two lower connection points of the
rechargeable battery at an angle in the battery
compartment sockets.
3. Fold the rechargeable battery in until it snaps audibly into
place.
Always disconnect the charger from the power supply if not
in use.
Charging the battery:
The rechargeable standard battery (EX) and the
rechargeable high-capacity battery (EX) may only be charged
using the Dräger X-plore 8000 standard charger or the Dräger
X-plore 8000 multiple charger.
1. Check to make sure that voltage of mains supply is
correct. The operational voltage of the power supply unit
must match the mains supply voltage.
2. Connect charger to power supply unit.
3. Connect the power supply unit to the mains supply.
4. First position the rechargeable battery at an angle in the
charger and then fold it in until it snaps audibly into place.
5. Wait for the end of the charging process.
6. When the rechargeable battery is fully charged, push the
battery lock button and remove the battery.
7. Disconnect the power supply unit and charger from the
mains supply.
| en
Maintenance
11