Publicité
Les langues disponibles
Les langues disponibles
TROUBLESHOOTING
Symptom
Sound cannot be heard.
"MISWIRING CHK WIRING THEN
RESET UNIT" / "WARNING CHK
WIRING THEN RESET UNIT" appears
and no operations can be done.
Source cannot be selected.
Radio reception is poor. / Static noise
while listening to the radio.
Correct characters are not displayed.
"PLEASE" and "EJECT" appear
alternately.
"IN DISC" appears.
Disc cannot be ejected.
Playback order is not as intended.
Elapsed playing time is not correct.
"NOT SUPPORT" appears and track
skips.
"CANNOT PLAY" flashes and/
or connected device cannot be
detected.
"READING" keeps flashing.
If you still have troubles, reset the unit. ( 3)
12
Remedy
• Adjust the volume to the optimum level.
• Check the cords and connections.
Check to be sure the terminals of the speaker wires are insulated
properly, then reset the unit. If this does not solve the problem, consult
your nearest service center.
Check the [SRC SELECT] setting. ( 4)
• Connect the antenna firmly.
• Pull the antenna out all the way.
This unit can only display uppercase letters, numbers, and a limited
number of symbols. The unit can also display uppercase Cyrillic letters.
( 11)
Press , then insert the disc correctly.
Make sure nothing is blocking the loading slot when you eject the disc.
Press and hold
to forcibly eject the disc. Be careful not to drop the
disc when it is ejected.
The playback order is determined by the file name (USB) or the order in
which files were recorded (disc).
This depends on the recording process earlier.
Check whether the track is a playable format. ( 11)
• Check whether the connected device is compatible with this unit and
ensure the files are in supported formats. ( 11)
• Reattach the device.
• Do not use too many hierarchical levels and folders.
• Reload the disc or reattach the USB device.
INSTALLATION / CONNECTION
Warning
• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery's negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car
chassis or Ground wire (black) to prevent a short circuit.
• Insulate unconnected wires with vinyl tape to prevent a short circuit.
• Be sure to ground this unit to the car's chassis again after installation.
Caution
• For safety's sake, leave wiring and mounting to professionals. Consult the
car audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal
parts of this unit during and shortly after use of the unit. Metal parts such
as the heat sink and enclosure become hot.
• Do not connect the
wires of speakers to the car chassis or Ground wire
(black), or connect them in parallel.
• Connect speakers with a maximum power of more than 50 W. If the
maximum power of the speakers is lower than 50 W, change the
[AMP GAIN] setting to avoid damaging the speakers. ( 9)
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal,
connect Ignition wire (red) to the terminal on the vehicle's fuse box
which provides 12 V DC power supply and is turned on and off by the
ignition key.
• After the unit is installed, check whether the brake lamps, blinkers,
wipers, etc. on the car are working properly.
• If the fuse blows, first make sure the wires are not touching car's chassis,
then replace the old fuse with one that has the same rating.
Basic procedure
1
Remove the key from the ignition switch, then
disconnect the
terminal of the car battery.
2
Connect the wires properly.
See Wiring connection. ( 14)
3
Install the unit to your car.
See Installing the unit (in-dash mounting).
4
Connect the
terminal of the car battery.
5
Reset the unit. ( 3)
Publicité
