Table des Matières
Publicité
We recommend to use correct sockets designed for use with
impact wrenches.
RIGHT-LEFT DIRECTION OF ROTATION
Choose direction of spindle rotation with the direction selector
switch (2) (fig. E).
Clockwise rotation – set the switch (2) to the extreme left position.
Counter-clockwise rotation – set the switch (2) to the extreme
right position.
* In certain cases position of the switch related to rotation may be different than
specified. Please refer to graphic signs located on the switch or tool body.
Safe position of the direction selector switch (2) is in the middle, it
prevents accidental starting of the power tool.
• When the switch is in this position, the power tool cannot be
started.
• Use this position of the switch to change sockets.
• Before starting the tool make sure the position of the direction
selector switch (2) is correct.
Do not change direction of rotation when the spindle of the
power tool is rotating.
Long lasting operation at low rotational speed of the spindle
may cause motor overheating. Make periodic breaks in operation
or allow the tool to operate at top speed without load for
approximately 3 minutes.
HOLDER
The power tool provides convenient holder (4) that allows to e.g.
hang the tool on a tool belt when working at heights.
OPERATION AND MAINTENANCE
MAINTENANCE AND STORAGE
• Cleaning the device after each use is recommended.
• Do not use water or any other liquid for cleaning.
• Clean the power tool, battery and charger with a dry cloth or blow
through with compressed air at low pressure.
• Do not use any cleaning agents or solvents, they may damage
plastic parts.
• Clean ventilation holes in the motor casing regularly to prevent
device overheating.
• Always store the power tool in a dry place, beyond reach of
children.
• Store the device with the battery removed.
All defects should be repaired by service workshop authorized by
the manufacturer.
TECHNICAL PARAMETERS
RATED PARAMETERS
Cordless Impact Wrench 58G018
Parameter
Battery voltage
Range of idle rotational speed
Tool holder
Max. torque
Protection class
Weight
Year of production
58G018 defines type and indication of the device
Battery
Battery voltage
Battery type
Battery capacity
Ambient temperature range
Charging time for charger 58G002
Weight
Year of production
Charger type
Supply voltage
Power supply frequency
Charging voltage
Max. charging current
Ambient temperature range
Charging time of the battery 58G001
Charging time of the battery 58G004
Protection class
Weight
Year of production
NOISE LEVEL AND VIBRATION PARAMETERS
Sound pressure
Sound power
Vibration acceleration
Noise and vibration information
Noise produced by the device is defined with: level of produced
sound pressure Lp
measurement uncertainty). Vibrations produced by the device
are defined with vibration acceleration value a
measurement uncertainty).
Sound pressure Lp
specified in this manual have been measured in accordance with EN
60745-1. Specified vibration level a
and for initial evaluation of exposition to vibrations.
Specified vibration level is representative for main applications
of the device. When the device is used for other purposes or with
Value
different working tools, the vibration level may change. Insufficient
or too rare maintenance may increase vibration level. The
18 V DC
abovementioned factors may lead to higher exposure to vibrations
0-2200 rpm
during whole working time.
To precisely define exposure to vibrations, include periods when
1/2" square
the device is switched off and when it is switched on but not used
180 Nm
for working. Once all factors have been carefully considered, total
exposition to vibrations may be significantly lower.
III
To protect the user from results of exposure to vibrations, use
additional safety measures such as: device and working tool periodic
1,8 kg
maintenance, proper hand temperature conditions, good work
2018
organisation.
13
Graphite Energy+ System Battery
Parameter
58G001
18 V DC
Li-Ion
2000 mAh
4
C – 40
0
1 h
0,400 kg
2018
Graphite Energy+ System Charger
Parameter
Lp
= 95,1 dB(A) K= 3 dB(A)
A
Lw
= 106,1 dB(A) K= 3 dB(A)
A
a
= 15,87 m/s
h
and level of sound power Lw
A
, sound power Lw
and vibration acceleration ah
A
A
can be used to compare tools
h
Value
58G004
18 V DC
Li-Ion
4000 mAh
C
4
C – 40
C
0
0
0
2 h
0,650 kg
2018
Value
58G002
230 V AC
50 Hz
22 V DC
2300 mA
4
0
C – 40
0
C
1 h
2 h
II
0,300 kg
2018
K= 1,5 m/s
2
2
(where K is
A
(where K is
h
Publicité
Table des Matières
