Extremis HOPPER picnic Instructions De Montage page 33

5. Put the tabletop with its frame facing downwards
on top of the two boards. The top of the legs are
now at the same height as the tabletop.
6. Position the legs to the tabletop.
7. a. Put 3 bolts M10x30 in the square holes of each
table leg. Screw the supplied nuts and spring
washers onto the threaded rods, but do not
tighten them yet.
b. Screw the supplied nuts and spring washers
into the threaded rods, but do not tighten them
yet.
8. Before assembling the benches, remove the
packaging material from under the frame!
9. Fasten the bench to the legs in the same way
described above. Now tighten all the nuts.
Floor fastening set - p16
1. Position the floor fastening plates on the inside
of the legs as shown on the drawing and mark the
holes on the ground.
2. Remove the plates and drill holes in the marked
locations.
3. Place the plates back and use the most
appropriate fasteners for the surface on which
the Hopper is to stand.
Floor fastening - p18
1. Mark the places on the floor where the fastening
plates are to be located.
2. Remove the table and drill holes in the marked
locations.
3. Use the most appropriate fasteners for the
surface on which the Hopper is to stand.
Hopper combo - p20
1. Remove the lid of the box. The packaging
material must stay intact for the rest of the
assembly!
2. Remove the four screws from the two boards
that prevent the table legs from moving during
transport. Fold down the cardboard flaps to
have better access to the legs. Take them out the
box and position them as shown in the drawing
(depending on the size of the table).
3. Put the lid back on the box.
4. Put the 2 boards mentioned in step 2 on top of
the lid.
5. Put the tabletop with its frame facing downwards
on top of the two boards. The top of the legs are
now at the same height as the tabletop.
6. Position the legs to the tabletop.
7. a. Put 3 bolts M10x30 in the square holes of each
table leg. Screw the supplied nuts and spring
washers onto the threaded rods, but do not
tighten them yet.
b. Screw the supplied nuts and spring washers
onto the threaded rods, but do not tighten them
yet.
8. Before assembling the benches, remove the
packaging material from under the frame!
9. Fasten the bench to the legs in the same way
described above. Now tighten all the nuts.
Backrest - p26
1. a. Unscrew the 2 nuts and spring washers at the
outside of the bench frame. Now also remove the
2 bolts M10x30. The bolt and nut on the insed will
prevent the bench from falling.
b. Unscrew the 2 nuts and spring washers at the
outside of the bench frame. The nut on the insed
will prevent the bench from falling.
2. a. Position the back supports on the bottom of
the bench and fasten it by inserting put 2 bolts
M10x40 in the square holes on either side and
screw 2 nuts & spring washer onto the threaded
rods.
b. Position the back supports on the bottom
of the bench and fasten it by 2 nuts onto the
threaded rods.
3. Screw the wooden shelf to the supports, each
time using 3 screws 5x25. Use the pre-drilled
holes to correctly position the backrest. Max. 10
Nm. Excessive force may break the head of the
screws.
Hopper table - p30
1. Lay the tabletop on trestles.
2. Position the legs to the tabletop.
3. a. Put 3 bolts M10x30 through the square holes
of each table leg. Screw the supplied nuts and
spring washers onto the threaded rods.
b. Screw the wooden shelf to the supports, each
time using 3 screws 5x25. Use the pre-drilled
holes to correctly position the backrest.
MAINTENANCE
Wood
DAY TO DAY CLEANING
Clean regularly and after every use
Wood doesn't need much maintenance, but the
better you treat it, the longer it will last. Cleaning
the wood regularly and immediately after use with
a damp cloth will prevent fluids from penetrating
deep into the wood. An oiled table will absorb liquids
less quickly, keeping it clean for longer. To remove
stubborn remains of dirt, simply use a stiff brush
and some water. Be careful not to permanently
damage the fibres. For this reason, never ever use a
high-pressure cleaner to clean wood.
33