Jacuzzi J-500 Série Manuel D'installation Et Utilisation Et Entretien page 45

guide you through the process of programming the spa to fit
your personal comfort.
ON UV
96
Heat & Filter
Heat and Filter: Tap (
heating and filtration programming.
Water Care
Water Care: Tap (
care programming.
Lock
>
Lock: Tap (
ming.
Time & Date
Time and Date: Tap (
time and date programming.
Language
Language: Tap (
programming.
Units
Units: Tap either
rature display.
Fº
Default setting is .
WiFi
>
Wi-Fi: Tap (
Back Button: Tap to go back to the previous menu.
Invert Button: Tap to invert the display image.
Slider Bar: Slide the bar up and down to view the se-
lections available.
I
Programming the Heating Mode
Your Jacuzzi spa is equipped with 3 modes of heating.
An automatic mode called "Auto, " where the spa's temperatu-
re is maintained at all times. An energy saving heating cycle
called "Econo. " A mode that will only activate the heater du-
ring the daytime called "Day" mode.
Note: The heater will activate when the temperature drops
~1° from the set temperature.
Indicates that the feature is active.
feature is not active.
HEAT & FILTER
Auto
Econo
Day
6:45 PM
SETTINGS
Heat & Filter
Water Care
WiFi
>
) to access the
>
to access the water
)
to access the locking program-
)
>
) to access the
>
access the language
)
Fº
Cº
or for the tempe-
) to access the Wi-Fi programming.
Indicates that the
Auto heating:
When programmed to "Auto, " the spa will maintain the water
temperature to the set temperature. Heating will occur when
necessary.
To select this mode, tap (
>
> Econo heating:
This is an energy saving heating program that allows the spa
>
to heat during non-peak hours. When programmed to "Eco-
no, " the spa will only be allowed to heat the water between
5:00 PM to 7:00 AM every day of the week. The hours cannot
be adjusted.
To select this mode, tap (
Day heating:
When programmed to "Day, " the spa will only be allowed to
heat the water between 7:00 AM to 5:00 PM every day of the
week. The hours cannot be adjusted.
To select this mode, tap (
I
Programming the Primary Filter
To access the "Primary Filter" feature, you need to use the Sli-
der Bar to scroll down to the "Heat & Filter" menu. Once you
scroll down, tap (
ming.
HEAT & FILTER
Auto
Econo
Day
During a primary filtration, the circulation pump, CLEARRAY
and ozone unit (if applicable) are activated. The factory default
cycle starts at 12:00 AM and last for 8 hours. If you elect to
keep this setting, then you can skip this section.
In extreme bitter cold weather we recommend you
program the circulation pump to run 24 hours.
Refer to the "Winterizing" section.
Any time the circulation pump runs outside of a program cy-
cle, e.g. for heating, that run time will be deducted from the
next primary filter cycle. For example, the primary filter cycle is
set to 8 hours every 24 hours but the circulation pump comes
on for 2 hours to heat the water after the cycle has finished.
The next primary filter cycle will only be for 6 hours not 8
hours.
Primary Filter
Start
12:00
8 00
pm
To change the default cycle:
Start
Tap to program the start time for the cycle.
Slide your finger up and down to roll the time scroll wheels
to adjust the start time.
45
next to the "Auto" icon.
)
next to the "Econo" icon.
)
next to the "Day" icon.
)
>
to enter the "Primary Filter" program-
)
HEAT & FILTER
Primary Filter
Secondary Filter
End
8:00
Set
>
>