Festo CMMP-AS-M3 Serie Mode D'emploi page 8

8 Technical data
General
CMMP-AS- C2-3A-M3
Dimensions and weight
Dimensions [mm] 202x66x207
1)
(HxWxD)
Mounting plate [mm] 248x61
dimensions
Weight [kg] 2.1
Approvals
CE marking (see declaration In accordance with EU Low Voltage Directive
of conformity)
In accordance with EU EMC Directive
In accordance with EU Machinery Directive
1) without plugs, screening screw and screw heads
Operating and environmental conditions
CMMP-AS- C2-3A-M3
General
Permitted installation height above sea level
at rated output [m] 1000
with power [m] 1000 ... 2000 (max.)
1)
reduction
Air humidity [%] 0 ... 90 (non-condensing)
Protection class IP20 (with plugged-in plug connectors at X6 and X9)
IP10 (without plugged-in plug connectors at X6 and X9)
Degree of contamination 2
Transport and storage
Temperature range [°C] -25 ... +70
Operation
Operating temper­ [°C] 0 ... +40
ature
Operating temper­ [°C] +40 ... +50
ature with power re­
duction 2.5 % per K
Shutdown temper­ °C 100
ature of power unit
heat sink
1) Above 1000 m above sea level Performance reduction of 1% per 100 m
Power supply [X9]
CMMP-AS- C2-3A-M3
Logic supply
Nominal voltage [V DC] 24 ±20 %
1)
Nominal current [A] 0.55
Maximum current [A] 1
2)
for holding brake
Load supply
Number of phases 1
Voltage range [V AC] 100 ... 230 ±10 %
Mains frequency [Hz] 50 ... 60
Alternative DC [V DC] 60 ... 380
supply
1) plus current consumption of a holding brake and I/Os, if present
2) for higher power requirements è Hardware description
All manuals and user guides at all-guides.com
C5-3A-M3 C5-11A-P3-M3, C15-11A-P3-M3
C10-11A-P3-M3
227x66x207 252x79x247
297x75
2.2 3.5
C5-3A-M3 C5-11A-P3-M3 C15-11A-P3-M3
C10-11A-P3-M3
80 80 85
C5-3A-M3 C5-11A-P3-M3 C15-11A-P3-M3
C10-11A-P3-M3
0.65 1
2
3
230 ... 480 ±10 %
60 ... 700
I/O interface [X1]
Type
Digital inputs/outputs
Inputs Input voltage
DIN0 ... DIN9
Voltage range
Outputs Output voltage
DOUT 0 ... DOUT3
1)
Voltage range
+24 V Output voltage
Max. output current
GND24 Voltage
When used as a digital input (configuration with FCT)
1)
I/O interface [X1]
Type
Analogue inputs/outputs
AIN0 Entry area
#AINO
Resolution
Time delay
max. input voltage
R
I
1)
AIN1 Entry area
Resolution
Time delay
1)
AIN2 Entry area
Resolution
Time delay
AMON0, AMON1 Output range
Resolution
Critical frequency
OGND Voltage
+VREF Output range
This input can also be optionally parameterised as a digital input with an 8 V switching
1)
threshold (parametrisation with FCT).
Supported encoders [X2A]/[X2B]
Encoder type Protocol
Resolver –
Digital encoder Incremental
Analogue encoder –
EnDat encoder EnDat 2.1 (01/21); EnDat 2.2 (22)
HIPERFACE encoder HIPERFACE
Details è Hardware description
Motor connection [X6]
1)
CMMP-AS- C2-3A-M3
Voltage [VAC] 0 ... 270
Rated output [kVA] 0.5
Max. power for 5 [kVA] 1
seconds
1) Data for operation at 1x230 VAC [±10 %], 50 ... 60 Hz
2) Data for operation at 3x400 VAC [±10 %], 50 Hz
è All available technical data è Hardware description.
Values Remark
[V] 24 active high, con­
forms to
[V] 8 ... 30
EN 61131-2
[V] 24 active high, gal­
vanically isolated
[V] 8 ... 30
[V] 24
[mA] 100
[V] 0 Reference poten­
tial for digital I/Os
Values Remark
[V] ±10 differential –
Bit 16
 250
[μs]
[V] 30
[kΩ] 30
[V] ±10 Single-ended –
Bit 10
 250
[μs]
[V] ±10 Single-ended –
[bit] 10
 250
[μs]
[V] ±10 –
[bit] 9
[kHz] 1
[V] 0 Reference
potential
[V] 0 ... 10 Reference output
for setpoint
potentiometer
Interface
[X2A]
[X2B]
[X2B]
[X2B]
[X2B]
1)
C5-3A-M3 C5-11A-P3- C10-11A-P3-
2) 2)
M3 M3
0 ... 360
1 3 6
2 6 12
C15-11A-P3
2)
-M3
9
18