Plunge Cutting - Milwaukee Sawzall M18 Fuel Manuel De L'utilisateur

Plunge Cutting

This MILWAUKEE Sawzall
ting directly into surfaces that can not be cut from
an edge, such as walls or floors. Plunge cutting may
be done two ways depending on how the blade is
inserted. Column A shows how to plunge cut with the
teeth of the blade facing downward. Column B shows
how to plunge cut with the teeth of the blade facing
upward. Do not plunge cut into metal surfaces (see
"Cutting Metals").
1. Insert the blade into the tool.
If you inserted the blade with the teeth facing
downward, hold the tool as shown in Column A,
resting the edge of the shoe on the workpiece.
If you inserted the blade with the teeth facing up-
ward, hold the tool as shown in Column B, resting
the edge of the shoe on the workpiece.
2. With the blade just above the workpiece, pull the
trigger. Using the edge of the shoe as a pivot, lower
the blade into the workpiece as shown.
3. As the blade starts cutting, raise the handle of
the tool slowly until the shoe rests firmly on the
workpiece. Then guide the tool along your cutting
line to acquire the desired cut.
NOTE: To make plunge cutting easier, use a heavy
gauge blade and install the blade with the teeth facing
upward as shown in Column B.
A
is ideal for plunge cut-
®
B
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
ONE-KEY™
Chemical Burn Hazard.
WARNING
This device contains a
lithium button/coin cell battery. A new
or used battery can cause severe in-
ternal burns and lead to death in as
little as 2 hours if swallowed or enters the body.
Always secure the battery cover. If it does not
close securely, stop using the device, remove the
batteries, and keep it away from children. If you
think batteries may have been swallowed or
entered the body, seek immediate medical atten-
tion.
Internal Battery
An internal battery is used to facilitate full ONE-KEY™
functionality.
To replace the battery:
1. Remove the battery pack.
2. Remove the screw(s) and open the battery door.
3. Remove the old battery, keep it away from children,
and dispose of it properly.
4. Insert the new battery (3V CR2032), with the posi-
tive side facing up.
5. Close the battery door and tighten the screw(s)
securely.
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
For repairs, return the tool, battery pack and charger
to the nearest service center.
6
Cleaning
Repairs