EINHELL TE-MG 300 EQ Instructions D'origine page 19

Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Mains voltage: ........................ 230-240 V ~ 50 Hz
Power input: .............................................. 300 W
Idling speed: ............................ 11000-20000 rpm
Sanding/grinding area: .............. 90 x 90 x 90 mm
Oscillation angle: ...........................................3,2°
Protection class: ............................................ II/
Weight: .....................................................1.83 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ........................ 78 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 89 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three
directions) determined in accordance with
EN 62841.
Handle
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in
accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may
vary from the level specifi ed during actual use,
Anl_TE_MG_300_EQ_SPK7.indb 19 Anl_TE_MG_300_EQ_SPK7.indb 19
= 2,277 m/s 2
h
2
- 19 -
GB
depending on the way in which the power tool is
used, especially the type of workpiece it is used
for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Fitting the plug-in tools (Figures 1/2/3)
•
Open the quick-release lock for changing
tools (5) as shown in Fig. 2.
•
To fit the plug-in tools safely you should
hold the multifunction tool so that the On/Off
switch (1) points down and the tool chuck (2)
faces up.
•
Place the plug-in tool (e.g. the scraper) on
the tool chuck (2) so that the pins of the tool
chuck fit into the recesses in the plug-in tool.
The tool chuck (2) is magnetic in order to
secure the plug-in tool during the clamping
12.05.2021 11:09:42 12.05.2021 11:09:42