Technical Features; User Safety - Jacuzzi Lodge Fiche Technique De Pre-Installation

It is the responsibility of the installer/owner to ascertain
compliance with specific local regulations prior to installa-
tion. Jacuzzi Europe S.p.A. gives no guarantee in this respect
and declines all responsibility regarding the compliance of
the installation performed.

Technical Features

Lodge ( 1) is available in the following versions:
- " blower" (with blower, filtering pump and heater or with ex-
changer);
- " hydro" (with 2-speed hydro pump and heater or with single-
speed hydro pump, filtering pump and exchanger);
- "hydro+blower" (with 2-speed hydro pump, blower and heater or
with single-speed hydro pump, filtering pump, blower and exchanger);
An additional heater (optional) is available to be connected to a sep-
arate power supply line (see also the "Electrical preparations" chapter).
Its power supply is single-phase (220/240 V), and all its electro-
mechanical organs and pipes are containedwithin its perimeter.
The skimmer contains 1 filtering cartridge (filtering surface: 4.6
2 2
m - 50 ft ) which guarantees optimal water filtration.
Maximum absorption of the system
" "
BLOWER ONLY VERSION
Total consumption
Power supply (x)
(with heater)
Volt Hertz Ampere
220-240 ~ 50/60 12 (k) 2,7(j)
" "
HYDRO VERSION
Total consumption
Power supply (x)
(with heater)
Volt Hertz Ampere
220-240 ~ 50/60 16 (k) 3,5 (j)
" + "
HYDRO BLOWER VERSION
Total consumption
Power supply (x)
(with heater)
Volt Hertz Ampere
220-240 ~ 50/60 18 (k)
(
SUPPLEMENTARY HEATER OPTIONAL
Power supply (x) Total consumption
Volt Hertz Ampere
220-240 ~ 50/60 26 (k)
Total consumption
(with heat exchanger)
kW Ampere kW Ampere
3,7 (k) 0,85 (j)
Total consumption
(with heat exchanger)
kW Ampere kW Ampere
8,8 (k) 1,95 (j)
Total consumption
(with heat exchanger)
kW kW
Ampere Ampere
4 (j) 11 (k) 2,6 (j)
)
kW
6 (j)
(k): at 230 V - (j): absorbed power
(x): see Chapter. "Electrical preparations"
HEAT EXCHANGER
- Primary inlet MAX temperature ....................................................50 °C
- Connections .......................................................................................... 3/4"
- Primary circuit flow rate ........................................................... 38 l/min
- Primary pressure drop ....................................................... 0,271 M H
The electrical system that powers the hot tub must absolutely
be sized for maximum consumption (as indicated in the respec-
tive tables).
Weights
Net weight
kg
~ 260
support
area
2
m
~ 2,98

User safety

If installed by qualified personnel in compliance with the in-
structions in the enclosed installation manual, the system does
not present any risks for the user. However, safety is also contin-
Spa-Pak
gent upon appropriate use, according to the provisions in the
(optional)
respective manual, while the user must delegate the operations
kW
described in the installation manual to qualified personnel.
2,5 (k)
0,5 (j)
It is important to make sure that personnel tasked to install
or manage the system are qualified as per legal requirements in
effect in the country where installation is carried out.
Spa-Pak
(optional)
Positioning the hot tub
( 2) The hot tub can be set against a wall, as shown, leav-
kW
ing the three sides free relative to the electromechanical
2,5 (k)
0,5 (j)
components located under the hot tub, making sure that it
can be inspected and the necessary maintenance can be per-
formed.
If you want to install the hot tub against multiple walls, a
Spa-Pak
space must be guaranteed for the removal of the panels and
(optional)
for any maintenance, and access must be guaranteed to the
equipment in the tub compartment.
kW
2,5 (k)
0,5 (j)
Prolonged sun exposure could damage the material
of which is made the hot tub shell, due to its capac-
ity to absorb heat (dark colours in particular). Don't
leave the hot tub to sun exposure without adequate
protection when not in use (cover thermal, gazebo,
etc.). Any damage arising by not following these
warnings are not covered by the guarantee.
11
average volume water volume
of use
MAX
litres litres
~ 880 ~ 1100
concentrated load
on support area
2
kg/ m
~ 456
O
2
Total max. weight
kg
~ 1360