Faro Ovni 33135 Installation Et Mode D'emploi page 14

INSTRUCCIONES DE SEGURIDAD / INSTRUCTION DE SÉCURITÉ / SAFETY INSTRUCTIONS / INSTRUÇÕES DE SEGURANÇA / SICHERHEITSHINWEISE / INSTRUCCIONES DE SEGURIDAD / INSTRUCTION DE SÉCURITÉ / SAFETY INSTRUCTIONS / INSTRUÇÕES DE SEGURANÇA / SICHERHEITSHINWEISE / INSTRUCCIONES DE SEGURIDAD / INSTRUCTION DE SÉCURITÉ / SAFETY INSTRUCTIONS / INSTRUÇÕES DE SEGURANÇA / SICHERHEITSHINWEISE /
VEILIGHEIDSINSTURCTIES / INSTRUZIONI DI SICUREZZA VEILIGHEIDSINSTURCTIES / INSTRUZIONI DI SICUREZZA / Ο∆ΗΓΊΕΣ ΑΣΦΑΛΕΊΑΣ / ИНСТРУКЦИИ ПО ТЕХНИКЕ
3 Push all connected wires up into junction box. 3 Push all connected wires up into junction box.
4. Slide the receiver in the mounting braked (fig. 4) and extend antenna along side mounting braked. 4. Slide the receiver in the mounting braked (fig. 4) and extend antenna along side mounting braked. 4. Slide the receiver in the mounting braked (fig. 4) and extend antenna along side mounting braked.
5. Reinstall the canopy on the mounting bra ck
6. Operating transmitter:
A. Install SF22 9 volt battery (not incl.) to prevent damage to transmitter, remove the battery if not use for long periods of time.
B. Store the transmitter away from excess hat or humidity. B. Store the transmitter away from excess hat or humidity.
C. This remote control unit is equipped with 16 code combinations to prevent possible interference from or to other remote units C. This remote control unit is equipped with 16 code combinations to
such as garage door openers, car alarms or security systems. If you find that your fan and light kit go on and off without us such as garage door openers, car alarms or security systems. If you find that your fan and light kit go on and off without us ing such as garage door openers, car alarms or security systems. If you find that your fan and light kit go on and off without us
your remote control, simply change the combination code in your tra your remote control, simply change the combination code in your tra nsmitter and receiver.
OPERATIONS BUTTONS ON THE TRANSMITTER: OPERATIONS BUTTONS ON THE TRANSMITTER:
1
2
3
•
The light function is controlled by pressing the light button. Hold button down to increase or decrease light. Tap button The light function is controlled by pressing the light button. Hold button down to in
quickly to turn light off or on.
•
Keep pressing the button for more than one second, the light becomes dimmer and varies cyclically from dim t bright and Keep pressing the button for more than one second, the light becomes dimmer and varies cyclically from dim t bright and Keep pressing the button for more than one second, the light becomes dimmer and varies cyclically from dim t bright and
back again.
Switch code setting labeled to "X" for no n- dimming light f unction: with non dimmable bulbs. Switch code setting labeled to "X" for no
with dimmer option on ONLY use
4
5
ck et.
(not incl.) to prevent damage to transmitter, remove the battery if not use for long periods of time. (not incl.) to prevent damage to transmitter, remove the battery if not use for long periods of time.
1- HI: for fan high speed HI: for fan high speed
MED: for fan medium speed MED: for fan medium speed
LOW: for fan low speed LOW: for fan low speed
2- OFF – on/off on/off
3- LIGHT for light brightness and off for light brightness and off (dimmer)
Switch code setting labeled to "D" for dimming light function. Use it with bulbs adapted for Switch code setting labeled to "D" for dimming light function. Switch code setting labeled to "D" for dimming light function.
dimmer
X
Con bombillas no dimeables : enciende y apaga la luz Con bombillas no dimeables
use bulbs adapted for it
4- CODES
5- DIMMER DIMMER
prevent possible interference from or to other remote units
unction: with non dimmable bulbs.
ТЕХНИКЕ БЕЗОПАСНОСТИ
crease or decrease light. Tap button