Table des Matières
Publicité
•
Offer this assembly into the threaded hole in the mounting plate as shown in picture A on page 1.
Please ensure no parts come in contact with any fairing panels. Finally tighten the crash protector bolts
until you feel some compression from inside the protector using 19mm socket and wrench. PLEASE
NOTE THE CRASH PROTECTOR MUST BE POSITIONED AS IN PICTURE 'C' WITH
BIGGER END TOWARD FRONT OF BIKE. Turn a little more so that you feel the compression
increase slightly. Tighten to 40Nm of torque (do not exceed this figure, as damage can occur to the
Page | 8
motorcycle and the bolt).
•
If not already fitted, fit bubble sticker into recess of crash protector cap (item 1).
•
Fit crash protector cap (item 1) into the crash protector.
Near side (left side as you sit on bike)
•
Place one of the M12 washers (item 3) onto the one of the M12 bolts (item 2) as shown in picture 20.
•
Place one of the locking washers (item 4) onto the bolt so it sits against the washer just fitted as shown
in picture 20.
•
Place the bolt with both washers into the crash protector (item 5) as shown in picture 20.
•
Offer this assembly into the threaded hole in the mounting plate as shown in picture B on page 1.
Please ensure no parts come in contact with any fairing panels. Finally tighten the crash protector bolts
until you feel some compression from inside the protector using 19mm socket and wrench. PLEASE
NOTE THE CRASH PROTECTOR MUST BE POSITIONED AS IN PICTURE 'C' WITH
BIGGER END TOWARD FRONT OF BIKE. Turn a little more so that you feel the compression
increase slightly. Tighten to 40Nm of torque (do not exceed this figure, as damage can occur to the
motorcycle and the bolt).
•
If not already fitted, fit bubble sticker into recess of crash protector cap (item 1).
•
Fit crash protector cap (item 1) into the crash protector.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes
which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer
acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G's
order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular
purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of
charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not
affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the
purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R&G's
or manufacturer's instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and
subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and
otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do
not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable
condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at
the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless
within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
Issue 1 20/07/2017 (NSY)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
Unit 1 Shelleys Lane, East Worldham, Alton, Hants GU34 3AQ
www.rg-racing.com
CP0428
Email:
info@rg-racing.com
Publicité
Table des Matières
