R&G CP0368BL Instructions De Montage page 14

tête du boulonM10 x 1.50 x 40mm (article 10) pour que la rondelle place contre la tête du
boulon.

Glisser une rondelle de blocage (article 7) sur le boulon pour qu'elle se place contre la
rondelle tout juste installée.

Glisser ensuite le boulon avec ses rondelles à travers la protection crash (article 6) pour que
la tête du boulon et les rondelles aillent dans le contre alésage.

Mettre la protection crash sur la plaque de montage sur l'axe puis serrer le boulon, comme
sur la photo 12.

Serrer le boulon de la protection jusqu'à ce que vous sentiez une compression de l'intérieur
de la protection avec une clé de 17mm. LA PROTECTION DOIT ETRE POSITIONNEE COMME
EN "C" AVEC LE COTE ARRONDI LE PLUS GROS EN DIRECTION DE L'AVANT DE LA MOTO.
Tourner un peu plus afin d'accentuer légèrement la compression. Faire un quart de tour.
Pas plus de 40 Nm de couple - Ne pas trop serrer, au risque d'abîmer les composants

Mettre les capuchons de protection crash dans les 2 protections.

Sur les 2 boulons arrière, les capuchons de caoutchoucs (article 5) son t fournis pour être
placés sur les têtes des boulons. Il est conseillé d'appliquer un peut se superglue ou du
silicone dessus pour s'assurer qu'ils restent en place.
Ces instructions sont disponibles au téléchargement sur
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer's statutory droites.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they
were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be
in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the
gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No
returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory droites and does
not refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1 19/05/2014 (AR)
CONSUMER NOTICE
R&G Racing
www.rg-racing.com
www.rg-racing.com
Email: info@rg-racing.com