Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Chevrolet Silverado 2500/2500HD/3500 2 & 4WD, Suburban 2500 2 & 4WD
GMC Sierra 2500/2500HD/3500 2 & 4WD, Yukon XL 2500 2 & 4WD
Receiver Shown In Proper Position
Hitch Requires 5/8" Pin and Clip
Equipment Required:
Fastener Kit: K65028
Wrenches: 3/4", 7/8", 18mm
Drill Bits: 9/16"
Pull Wire
Vehicles With
OEM Tow Hooks
1
Qty. (4)
Hex Nut, M12 x 1.75 x 45
2
Qty. (2)
Carriage Bolt, 1/2"-13 x 1-3/4"
3
Qty. (2)
Spacer, 2" x 1.5" x 1/4"
4
Qty. (2)
Lock Washer, 1/2"
1.
If vehicle is equipped with OEM tow hooks remove tow hook fasteners from inside of frame and bottom of frame and return to vehicle
owner.
2.
Raise hitch into position and install fasteners as shown above. Use 1/2" flat washers as spacers between hitch and side of frame if necessary.
3.
Due to variations in tow hook mounting holes, it may be necessary to enlarge 1/2" holes in hitch to 9/16" holes.
NOTE: Fascia trimming is optional on 2500 h.D./3500 models. CONSULT VEHICLE OWNER BEFORE TRIMMING.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. A hitch or ball which has been damaged should be removed and replaced.
Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. Do not cut, weld, or
modify hitch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2006 Cequent Towing Products
Front Mounted Receiver
Installation Instructions
(Vehicles With Amber Turn Signals)
Fascia Has To Be
Pushed Up 1-1/2"
on 2002 And
Later Vehicles
Frame Rail
Tow Hook
Tighten all 1/2" GR5 fasteners with torque wrench to 75 Lb.-Ft (102 N-m).
Tighten all M12 CL10.9 fasteners with torque wrench to 75 Lb.-Ft (102 N-m).
CARGO CAPACITY – DO NOT EXCEED
500 LB. OR VEHICLE FRONT GROSS
AXLE WEIGHT RATING. (GAWR)
9000
Orient Spacer
As Shown
Vehicles With
OEM Tow Hooks
5
Qty. (4)
Conical Washer, 1/2"
6
Qty. (2)
Hex Nut, 1/2"
7
Qty. (4)
Hex Nut, M12
8
Qty. (2)
Flat Washer, 1/2"
Sheet 1 of 3
N65028
Part Numbers:
65028
LB. MAX. WINCH LINE PULL
Vehicles Without
OEM Tow Hooks
Vehicles Without
OEM Tow Hooks
6-23-06
Rev. B
Publicité
Manuels Connexes pour Cequent Towing Products 65028
Sommaire des Matières pour Cequent Towing Products 65028
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N65028 6-23-06 Rev. B 2006 Cequent Towing Products...
- Page 2 Ne pas découper, souder ni modifier l’attelage. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage Feuille 2 de 3 N65028 6-23-06 Rev. B 2006 Cequent Towing Products...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 N65028 6-23-06 Rev. B 2006 Cequent Towing Products...