Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required: ¾" crow foot
Fastener Kit: 24836F
Wrenches: m13, 3/4"
Drill Bits: none
USE 3/4" CROW FOOT
TO TORQUE BOLT
View A
TRUNK
PAN
1
Qty. (1)
BOLT – HEX HEAD – 1/2"-13 X 4" LONG
2
Qty. (1)
CONICAL WASHER – 1/2"
3
Qty. (1)
WASHER – HARDEN FLAT
1.
Raise vehicle on ramps or hoist.
2.
Remove existing m8 nuts from exhaust hangers.
3.
Lift passenger side of hitch over muffler, forward of exhaust hanger.
4.
By gently pulling down on the driver's side muffler, slide the driver's side of hitch over the tail pipe and forward into position.
5.
Hitch will be mounted between heat shield and muffler exhaust hangers using existing studs.
6.
With hitch in place, raise exhaust hangers back on their studs and start the m8 nuts (keep loose for now).
7.
Place 1/2" conical washer in place then install 1/2" bolt.
8.
Install 1/2" flat washer and nut.
9.
Tighten m8 nuts and then the 1/2" fastener with torque wrench.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2009 Cequent Towing Products
Installation Instructions
Audi A6
Drawbar Kit:
3593
Drawbar must be used in the
rise position only.
1
2
3
4
5
4
5
Tighten all 1/2" fasteners with torque wrench 75 Lb.-Ft. (102 n*m)
Tighten all M8 fasteners with torque wrench to 25 Lb.-Ft. (34 n*m)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg.) Max Gross Trailer Weight
200 LB (90.8 Kg.) Max Tongue Weight
Wiring Access Location: PC1, PC2
View A
5
Qty. (1)
NUT - 1/2"-13
Qty. (4)
NUT - M8 X1.25 FLANGED LOCKING
24836N
Part Numbers:
24836
60238
EHXUAST HANGER
MUFFLER
RUBBER
ISOLATOR
1-30-09
Rev. A
Form F206 Rev A 5605
Publicité
Manuels Connexes pour Cequent Towing Products 24836
Sommaire des Matières pour Cequent Towing Products 24836
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24836N 1-30-09 Rev. A 2009 Cequent Towing Products Form F206 Rev A 5605...
- Page 2 Ne jamais utiliser une torche pour découper un accès ou un trou de fixation. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24836N 1-30-09 Rev. A 2009 Cequent Towing Products Form F206 Rev A 5605...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Sheet 3 of 3 24836N 1-30-09 Rev. A 2009 Cequent Towing Products Form F206 Rev A 5605...