Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required: Utility Knife
Fastener Kit: 24808F
Wrenches: 10mm, 14mm, 17mm,
Small Flat Head Screwdriver
Frame rail
2
1
1
Qty. (4)
Bolt M10 X 1.25 X 30mm CL 8.8
1.
Remove plastic cover panel from underneath the driver side of the vehicle.
2.
Remove tow hooks if present. Return tow hooks & fasteners to owner.
3.
Raise hitch into position and install fasteners into existing weldnuts as shown above.
4.
Torque all fasteners to specifications shown below.
5.
Plastic cover panel will need to be trimmed or not reinstalled on vehicle. Obtain vehicle owners approval before cutting.
With permission: Enlarge tow hook slot on plastic cover panel to fit around drivers side bracket.
6.
Reinstall trimmed cover panel removed in Step 1. Or return untrimmed panel to vehicle owner.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2008 Cequent Towing Products
Installation Instructions
Drawbar Kit:
3593
Drawbar must be used in the
RISE position only.
Note: Fasteners typical
both sides
Tighten all M10 CL8.8 fasteners with torque wrench to 35 Lb.-Ft. (47 N*M)
Toyota Prius
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC1,2
Tow hook slot
Area to be trimmed
Remove plastic rivet
NOTE! Plastic cover panels will need to be trimmed or not
reinstalled on vehicle. Get owner's permission before starting
installation.
2
Qty. (4)
Conical Washer
Sheet 1 of 3
Part Numbers:
Manufacturer's Rating or
Weldnuts, typical both sides
M6 bolts
24808N
2-21-08
24808
60894
77179
Rev. A
Publicité
Manuels Connexes pour Cequent Towing Products 24808
Sommaire des Matières pour Cequent Towing Products 24808
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24808N 2-21-08 Rev. A 2008 Cequent Towing Products...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 of 3 24808N 2-21-08 Rev. A 2008 Cequent Towing Products...
- Page 3 No corte el acceso o los orificios del accesorio con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 of 3 24808N 2-21-08 Rev. A 2008 Cequent Towing Products...