Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: F24711
Wrenches: 7/8"
EXISTING HOLE
Drill Bits: 1/2"
IN FRAME RAIL
EACH SIDE
DRILL HOLE
IN FRAME RAIL
EACH SIDE
1 1 1 1
Qty. (4)
Bolt, Carriage 1/2-13 x 1.75
2 2 2 2
Qty. (4)
Block, 0.25 x 1.50 x 2.00
1. FISHWIRE BLOCK AND CARRIAGE BOLT THROUGH ACCESS HOLE AT TOP OF FRAME RAIL AND INTO EXISTING HOLES.
2. RAISE HITCH INTO POSITION AND SECURE WITH CONICAL TOOTHED WASHERS AND NUTS.
3. USING FORWARDMOST SLOT IN HITCH AS A TEMPLATE, DRILL 1/2" HOLE INTO FRAME RAIL, EACH SIDE.
4. FISHWIRE REMAINING BLOCKS AND CARRIAGE BOLTS INTO THE HOLES DRILLED IN STEP3. SECURE WITH CONICAL TOOTHED
WASHERS AND NUTS.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z 2006,2007,2015 Cequent Towing Products – Printed in Mexico
Installation Instructions
CHRYSLER SEBRING
CONVERTIBLE
(Sold separately)
Drawbar Kit:
3592
Drawbar must be used in the
RISE position only.
FRAME RAIL
ACCES HOLE AT
TOP OF FRAME RAIL
1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4
Tighten all 1/2-13 fasteners with torque wrench to 75 Lb.-Ft.
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
3 3 3 3
Qty. (4)
Washer, Conical Toothed
4 4 4 4
Qty. (4)
Nut, 1/2-13
N24711
Part Numbers:
24711
77092
60850
Manufacturer's Rating or
Wiring Access Location: PC3, PC4
ACCES HOLE AT
TOP OF FRAME RAIL
FRAME
DRILLED HOLE
EXISTING
HOLE
KINK FISHWIRE
TO KEEP BLOCK
INDEPENDENT OF BOLT
EXAMPLE OF FISHWIRE PROCEDURE
10-19-15
Form F206 Rev A 5605
Rev. D
Publicité
Manuels Connexes pour Cequent Towing Products 24711
Sommaire des Matières pour Cequent Towing Products 24711
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N24711 10-19-15 Rev. D z 2006,2007,2015 Cequent Towing Products – Printed in Mexico Form F206 Rev A 5605...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 N24711 10-19-15 Rev. D z 2006,2007, 2015 Cequent Towing Products - Imprimé au Mexique Form F206 Rev A 5605...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 N24711 10-19-15 Rev. D z 2006,2007,2015 Cequent Towing Products - Impreso en México Form F206 Rev A 5605...