Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Fascia
Spare Tire
Bumper
Well
Hitch Shown In Proper Position
Equipment Required: Pull Wire (provided)
Fastener Kit: 24750F
Wrenches: 3/4, 7/8, 11/16
Drill Bits: None
15
Pull Wire
Bumper Fascia
Hitch Uprights
98
Hitch Side Arm
1
Qty. (2)
Carriage Bolt 7/16-14 X 1-1/2
2
Qty. (2)
Carriage Bolt ½-13 x 2-1/4
3
Qty. (2)
Block ¼ x 2 x 2
4
Qty. (2)
Block ¼ x 1-3/4 x 2-1/2
5
Qty. (2)
Block ¼ x 1 x 3
1.
Open trunk, lift rug and remove spare tire.
2.
Remove both rubber sealing plugs from the bottom of spare tire well. Install carriage bolts and blocks as shown, longer bolt in rearmost hole.
3.
Remove (2) plastic fascia push rivets from bottom of rear bumper fascia and retain for re-installation.
4.
Position hitch uprights above fascia and loosely attach blocks, conical washers and nuts at spare tire well attachments as shown. Be sure to
install spacer blocks between hitch side arm and rearward attachment to spare tire well as shown.
5.
Install blocks and carriage bolts into slots in bumper and down thru slots in hitch uprights using pull wire provided as shown. Install conical
washers and nuts
Note: Kink pull wire to keep block independent of bolt as shown in Figure 2.
6.
Reinstall push rivets back into bumper fascia.
7.
Apply sealant at carriage bolt attachments inside spare tire well to prevent the intrusion of water and exhaust fumes to vehicle interior.
8.
Replace spare tire and rug.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005, 2006 Cequent Towing Products
Installation Instructions
Nissan Sentra
Drawbar Kit:
3593
Drawbar must be used in the
Rise position only.
Bumper
67
1598
Figure 1
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4
Bumper
Existing hole
Example of pull wire procedure
Apply sealant
23
Between blocks
And well
4
Remove rubber
Sealing plugs
6
Qty. (2)
Conical Toothed Washer ½"
7
Qty. (2)
Hex Nut ½-13
8
Qty. (2)
Hex Nut 7/16-14
9
Qty. (2)
Conical Toothed Washer 7/16
Sheet 1 of 3
24750N
Part Numbers:
24750
77126
60826
Kink pull wire to keep block
independent of bolt
Figure 2
Spare Tire
23
Well
67
10/27/06
Form F206 Rev A 5605
Rev. D
Publicité
Manuels Connexes pour Cequent Towing Products 24750
Sommaire des Matières pour Cequent Towing Products 24750
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24750N 10/27/06 Rev. D 2005, 2006 Cequent Towing Products Form F206 Rev A 5605...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24750N 10/27/06 Rev. D 2005, 2006 Cequent Towing Products Form F206 Rev A 5605...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 24750N 10/27/06 Rev. D 2005, 2006 Cequent Towing Products Form F206 Rev A 5605...