Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24795F
Wrenches: 17mm,19mm, Small Philips
Tip Screwdriver
Drill Bits: None
Note:
Fasteners typical
both sides.
Minor Fascia trim required.
Obtain vehicle owner's
approval before cutting
1 1 1 1
Qty. (4)
Bolt M12 x 1.25 x 40mm CL8.8
2 2 2 2
Qty. (4)
Conical washer – ½"
3 3 3 3
Qty. (4)
Bolt M10 x 1.25 x 40mm CL8.8
Note: Due to different configuration of the vehicle there will be extra hardware left over.
•
Using a small Philips tip screwdriver, unscrew plastic screws while applying pressure to the opposite end (3) places. Both
pieces of plastic need to be removed from support straps.
•
Elantra and Rio 5 models: Trim center fascia tab. Obtain vehicle owner's approval before cutting. See figure 2.
•
Lower vehicle exhaust by removing rubber exhaust hanger.
•
Lift hitch into position, passenger side first. Place crosstube over top of tail pipe, with the side bracket as far into space behind
wheel well, rotate into position on the outside of the frame rail. It will be necessary to pull the fascia gently out of the way. See
Figure 2.
•
Raise the drivers side of the hitch into position on the outside of the frame rails and in front of bulkhead. Once again pull the
fascia gently out of the way. See Figure 2.
•
Install fasteners as shown in Figure 1. Hand tighten fasteners.
•
Push hitch toward the rear of the vehicle and tighten all fasteners.
•
Reattach rubber muffler hanger.
•
Reattach fascia tabs.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007 Cequent Towing Products
Installation Instructions
Hyundai Elantra
Hyundai Accent 3-Door
Kia Rio 5
Drawbar Kit:
3594
Drawbar must be used in the
RISE position only.
Frame rail
Existing weldnuts
Exhaust not shown
for clarity
Figure 1
Tighten all M10 CL 8.8 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)
Tighten all M12 CL 8.8 fasteners with torque wrench to 76 Lb.-Ft. (103 N*M)
(Fascia trim required)
(Fascia trim required)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4 (Rio 5 and Elantra)
Bulkhead
4 4 4 4
Qty. (4)
Conical Washer – 3/8"
5 5 5 5
Qty. (4)
Spacer – 3/8 x 1-1/2 x 3
Sheet 1 of 3
24795N
Part Numbers:
24795
60872
77167
PC1, PC2 (Accent)
Trim this fascia tab
Rio 5 and Elantra Only
Pull fascia in
this area
Figure 2
Rio 5 and Accent
5
Only
1
2
Rio 5 and Accent
Only
3 4
Elantra Only
2-5-07
Rev. A
Form F206 Rev A 5605
Publicité
Manuels Connexes pour Cequent Towing Products 24795
Sommaire des Matières pour Cequent Towing Products 24795
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24795N 2-5-07 Rev. A 2007 Cequent Towing Products Form F206 Rev A 5605...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24795N 2-5-07 Rev. A 2007 Cequent Towing Products Form F206 Rev A 5605...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 24795N 2-5-07 Rev. A 2007 Cequent Towing Products Form F206 Rev A 5605...