Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Stabilizer Bar
Stabilizer Bar Bracket
Receiver Shown In Proper Position
Hitch Requires 5/8" Pin and Clip
Equipment Required:
Fastener Kit: K65017
Wrenches: 10mm, 15mm,
17mm, 3/4"
Drill Bits: None
* 93-97 Ford Ranger
* Mazda B Series
With Fog Light Option
(Round Light)
Cut
FIGURE 1
1
Qty. (2)
Hex Bolt, 1/2"-13 x 1-3/4"
2
Qty. (2)
Conical Washer, 1/2"
**NOTE: All Mazda vehicles and '93 through -97 Ford Rangers with fog light option require extensive fascia cut. See Figure 1.
CONSULT VEHICLE OWNER.
1.
Remove front air dam (if present).
2.
Remove stabilizer bar fasteners.
3.
Raise receiver into position, sandwiching stabilizer bar bracket between receiver and frame rail, and install all fasteners as shown in
Figure 2.
4.
If desired, trim and reinstall the front air dam. CONSULT VEHICLE OWNER BEFORE TRIMMING.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. A hitch or ball which has been damaged should be removed and replaced.
Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. Do not cut, weld, or
modify hitch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005 Cequent Towing Products
Front Mounted Receiver
Installation Instructions
*Ford Ranger, Ford Explorer
*Mazda B-Series Truck, *Mazda Navajo
**See Note Below and Figure 1
Frame Rail
Bumper
Existing Weldnuts
Typical Both Sides
Truck & Navajo
(Rectangular Light)
Section
To Be
Stabilizer Bar
Removed
Tighten all M10 fasteners with torque wrench to 42 Lb.-Ft (57 N-m).
Tighten all 1/2" CL9.8 fasteners with torque wrench to 50 Lb.-Ft (68N-m).
CARGO CAPACITY – DO NOT EXCEED
300 LB. OR VEHICLE FRONT GROSS
Frame Rail
Stabilizer Bar
Bracket
3
Qty. (2)
4
Qty. (4)
Sheet 1 of 3
AXLE WEIGHT RATING. (GAWR)
LB. MAX. WINCH LINE PULL
9000
FIGURE 2
Handle Nut, 1/2"
Hex Bolt, M10 x 1.75 x 45
N65017
11-07-05
Part Numbers:
65017
Recovery Eye
Rev. A
Publicité
Manuels Connexes pour Cequent Towing Products 65017
Sommaire des Matières pour Cequent Towing Products 65017
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N65017 11-07-05 Rev. A 2005 Cequent Towing Products...
- Page 2 Ne pas découper, souder ni modifier l’attelage. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage Feuille 2 de 3 N65017 11-07-05 Rev. A 2005 Cequent Towing Products...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 N65017 11-07-05 Rev. A 2005 Cequent Towing Products...