Technical Specifications Of Product Components - Nice Mhousekit Ws200S Instructions Et Avertissements Pour L'installation Et L'utilisation

WS200S is manufactured by NICE S.p.a. (prov. of Treviso – Italy). Nice S.p.a., in order to improve its products, reserves the right to modify their
technical characteristics at any time without prior notice. In any case, the manufacturer guarantees their functionality and fitness for the intended
purposes. Note: all the technical characteristics refer to a temperature of 20°C.
Model:
Type
Technology adopted
Peak thrust
Nominal torque
Speed (no load)
Nominal torque speed
Maximum cycles frequency
Maximum continuous cycle time
Operating limits
Mains powered WS100SCK - WS100SK
Nominal absorbed power
Nominal absorbed current
Emergency power supply
FLASH output
ECSbus output
"OPEN" input
"STOP" input
Radio Antenna input
Maximum cable length
Ambient operating temperature
Use in acid, saline or potentially
explosive atmospheres
Mounting
Protection rating
Dimensions / weight
Remote control compatibility
Memorisable GTX4 transmitters
Programmable functions
Self-programming functions
24 – English

TECHNICAL SPECIFICATIONS OF PRODUCT COMPONENTS

WS100SCK
Electromechanical gearmotor for automation of automatic gates and doors with incorporated
command control unit, complete with radio receiver for "GTX4" transmitters.
24Vdc motor, reducer with helical gears; mechanical release. A transformer inside the motor, but
separate from the control unit, reduces the mains voltage to the nominal 24 V
all of the automation system.
150 Nm
50 Nm
1.7 RPM
1.4 RPM
20 cycles/hour at 50°C
5 minutes
The structural features make it suitable for use on gates with a weight of up to 150kg and a leaf
length of up to 2.2 m. Opening angle of 110°
230 V (+10% -10%) 50/60Hz
150 W; at peak the power is 250 W for a
maximum duration of 1s
Provision for "PR1" buffer battery
For traffic lights: flashing light indicator lamp of 12 V maximum 21 W, Courtesy light lamp 24 V
maximum 4 W, Gate open indicator lamp 24 V maximum 4 W
One output with maximum load of 15 ECSbus units
For normally open contacts (the closing of the contact causes the "OPEN or Pedestrian
Opening" command)
For normally closed or normally open contacts and/or for constant resistance of 8.2 KΩ, or
normally closed contacts with self-recognition of the "normal" state (any variation from the
memorised status causes the "STOP" command)
50Ω for RG58 or similar type of cable
Mains power supply: 30 m; inputs/outputs: 20 m with antenna cable preferably shorter than 5m
(observe the warnings regarding minimum gauge and type of cables)
-20 ÷ 50°C
NO
On a horizontal plane using the appropriate mounting plate
IP54
237 x 155 x h 290 mm / 7 kg
Using GTX4 transmitters, the control unit is able to receive one or more of the following
commands: "OPEN", "Partial Open", "Open Only" and "Close Only"
This range can vary if there are obstacles or electromagnetic disturbances, and is affected by
the position of the receiving aerial incorporated in the flasher
"Cycle" or "Complete cycle" (automatic closure) functionality
"Slow" or "fast" motors speed
Pause time during "complete cycle", selectable from 10, 20, 40, 80 seconds
Partial opening type selectable in 4 modes
Obstacle detection system sensitivity, 4 selectable levels
"OPEN" command functionality selectable in 4 modes
Open input configuration on the control unit: open or pedestrian opening
FLASH output configuration: flashing light, courtesy light or gate open indicator
Motors discharge on closure selectable from 8 levels
Motors discharge on opening selectable from 8 levels
Auto-recognition of devices connected to the ECSbus output
Auto-recognition of the type of "STOP" device (NO or NC contact or 8.2 KΩ resistance)
Recognition of the opening angle for each motor
Automation recognition with 1 or 2 motors
WS100SK
voltage used in
24 Vdc
2 A, at peak power the maximum current is 4
A for a maximum duration of 1s
237 x 155 x h 290 mm / 6.2 kg