Grinder Safety Warnings - Makita 9556PB Manuel D'instructions

ENGLISH
(Original instructions)
1 Shaft lock
2 Lock-off lever
3 Switch lever
4 Lock button
5 Wheel guard
6 Bearing box
7 Screw
SPECIFICATIONS
Model
Depressed center wheel diameter.......................... 100 mm
Max. wheel thickness ............................................. 6.4 mm
Spindle thread ....................................................... M10
Rated speed (n) / No load speed (n
Overall length ........................................................ 273 mm
Net weight ............................................................. 2.0 kg
Safety class ...........................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:
1. This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read
all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
2. Operations such as polishing are not recom-
mended to be performed with this power tool.
Operations for which the power tool was not designed
may create a hazard and cause personal injury.
4
Explanation of general view
8 Lock nut
9 Depressed center grinding
wheel/Multi-disc
10 Inner flange
11 Lock nut wrench
12 Abrasive disc
13 Rubber pad
9556PB
) .................... 11,000 min
0
/II
ENE048-1
ENF002-2
GEA010-1
GEB033-7
14 Wire cup brush/Wire bevel brush
15 Abrasive cut-off wheel/diamond
16 Wheel guard for abrasive cut-off
17 Exhaust vent
18 Inhalation vent
9557PB
115 mm
6.4 mm
M14
-1
11,000 min
273 mm
2.1 kg
/II
3. Do not use accessories which are not specifi-
cally designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
4. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories can-
not be adequately guarded or controlled.
6. Threaded mounting of accessories must match
the grinder spindle thread. For accessories
mounted by flanges, the arbour hole of the
accessory must fit the locating diameter of the
flange. Accessories that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
7. Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad for
cracks, tear or excess wear, wire brush for loose
or cracked wires. If power tool or accessory is
dropped, inspect for damage or install an undam-
aged accessory. After inspecting and installing
an accessory, position yourself and bystanders
away from the plane of the rotating accessory
and run the power tool at maximum no-load
speed for one minute. Damaged accessories will
normally break apart during this test time.
8. Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear dust
mask, hearing protectors, gloves and workshop
apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be
capable of stopping flying debris generated by vari-
ous operations. The dust mask or respirator must be
capable of filtrating particles generated by your oper-
ation. Prolonged exposure to high intensity noise
may cause hearing loss.
wheel
wheel/diamond wheel
9558PB
125 mm
6.4 mm
M14
-1 -1
11,000 min
273 mm
2.1 kg
/II