Using Your Air Conditioner - Whirlpool WHAP121AW Guide D'utilisation Et D'entretien

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

USING YOUR AIR CONDITIONER

Appearance may vary.
Turning the Air Conditoner ON or OFF
Press POWER to turn the air conditoner ON or OFF.
IMPORTANT:
If you turn off the air conditioner, wait at least 3
minutes before turning it back on. This prevents
the air conditioner from blowing a fuse or
tripping a circuit breaker.
Do not try to operate your air conditioner in the Cool mode
when outside temperature is below 65°F (18°C). The inside
evaporator coil will freeze up, and the air conditioner will not
operate properly.
NOTE: In the event of a power failure, your air conditioner will
operate at the previous settings when the power is restored.
Display
During normal operation display will show the current room
temperature. When the TEMP/TIME t and s buttons are
pressed, the unit will display the set temperature or delay time.
Selecting the Mode
The Mode button has three settings:
Cool
Dehumidify
Fan
Press the MODE button until the indicator light
above the desired setting is lit.
Cooling (COOL) Mode
In cooling mode, the air conditioner cools air from the room and
vents hot air to the outdoors through the vent hose(s). Adjust fan
speed and the temperature setting to fit your desired comfort
level. Temperature-setting range is 61°F–90°F (16°C–32°C).
IMPORTANT: The vent hose(s) must exhaust to the outdoors
when using Cool mode.
Dehumidify (DEHUM) Mode
Air is dehumidified as it passes through the unit, without being in
full cooling mode. The fan will operate at medium speed.
Fan speed is not adjustable in dehumidify mode.
IMPORTANT: The vent hose(s) must exhaust to the outdoors
when using Dehumidify mode.
Fan (FAN) Mode
In this mode, only the fan will run. Air is circulated through the
room with no cooling.
NOTE: The air conditioner does not need to be vented to the
outdoors in Fan mode.
8
Selecting the Fan Speed
The Fan Speed has 3 settings:
LOW
Medium (MED)
HIGH
Press the SPEED button until the indicator light
above the desired setting is lit.
Adjusting the Temperature
Press the TEMP/TIME s and t
buttons to adjust the set temperature
up or down in 1° increments.
Temperature setting range is
61°F–90°F (16°C–32°C). After 10
seconds, the display will return to the current room temperature.
NOTE: Temperature may only be adjusted in cooling mode.
When in TIMER mode, pressing the TEMP/TIME s and t
buttons will adjust the delay time for the air condtioner to shut
off or turn on.
Switching between Fahrenheit and Celsius:
Press both s and t buttons at the same time to toggle the
displayed units between °F and °C.
Using the Timer
Auto Shut-Off
You can set the air conditoner to shut off
automatically after a set number of hours, up to 24
hours.
To set Auto Shut-Off:
1. With the air conditioner in fan mode, press
TIMER.
2. Use the TEMP/TIME s and t buttons select number of
hours, up to 24 hours.
3. After the set time, the air conditioner will turn off automatically.
Auto Start
You can set the air conditioner with the TIMER to start
automatically after a set number of hours.
1. With the air conditoner OFF, press TIMER.
2. Use the TEMP/TIME s and t buttons to select the number
of hours before the air conditioner should turn on, up to 24
hours. The TIMER indicator light will remain lit to let you know
the timer is set.
3. After the set time, the air conditioner will start automatically in
Cool mode with the last temperature and fan settings used.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Whap141awWhap122awWhap142aw

Table des Matières