Publicité
Les langues disponibles
Les langues disponibles
Warnings – Assembly text instructions – Maintenance
English
WARNINGS
General
•
Do not use any sharp tools to open the
packaging.
•
We strongly advise against using power tools.
•
Tripping hazard, mind your step.
•
Do not put out cigarettes on the table.
•
Not grafitti proof.
•
Do not leave children unattended whilst playing
on the table.
•
away from babies and children.
•
Colors can differ over years and from batch to
batch.
Product
•
Do not drag the table, but carry it with minimum
2 people.
•
Anchoring the product has to be done by
qualified people.
•
For anchoring: use suitable bolts or screws from
a specialized store depending on the material
your terrace is made of.
•
180 cm: max. 4 people or 320 kg per bench - 240
cm: max. 5 people or 400 kg per bench - 300
cm: max. 6 people or 480 kg per bench - 360 cm:
max. 7 people or 560 kg per bench
•
Regularly clean the flat surface of the legs.
Powder-coating
•
White powder-coating requires more
maintenance.
•
Do not use abrasive scouring powders or
scourers as they will scratch the surface.
•
Color can fade to some extent when exposed to
UV.
•
Flame retarding - NEN-EN13501-1 A2-sl -
Satisfying the same criteria as Class B for the
SBI-test according to EN13823. In addition,
under conditions of a fully developed fire these
products will nog significantly contribute to the
fire load and fire growth.
•
Dark colors can get very hot in sunny weather.
Sunbrella
•
Not waterproof, store inside!
•
Shake or brush off loose dirt immediately.
•
UV color fasteness: 7/8 (ISO 105-B02).
24
ASSEMBLY INSTRUCTIONS
Hopper picnic AA - p8
1. Slide the lid off the packaging and remove the four
screws from the two boards that secure the picnic
legs during transport. Bend the flaps outwards so
that the table legs are easily accessible. Now take
the legs out of the box, placing them as shown in
the drawing (depending on the table size).
2. a. Put the lid back on the box.
b. Position the isomo & wooden boards on top of
the box as shown in the drawing.
3. Put the tabletop on top of the wooden boards. The
top of the legs are now at about the same height as
the tabletop.
4. Fix the four endcaps as shown in the drawing.
5. Now attach the legs to the tabletop.
6. Attach each leg with three M10 spring washers and
M10 nuts, but do not fully tighten them yet.
7. Before mounting the benches, remove the box from
under the table!
8. a. Slide the bench over the screw-thread of the legs.
TIP: To prevent lacquer damage, it is best to mount
the bench from bottom to top.
b. Make sure that the sloping sides of the benches
match the sloping sides of the legs, as shown in the
drawing.
9. Now mount the bench frame to the legs in the same
manner, each with two M10 spring washers and
M10 bolts. Only then can all the nuts be tightened.
Hopper combo AA - p14
1. Slide the lid off the packaging and remove the
four screws from the two boards that secure
the picnic legs during transport. Bend the
flaps outwards so that the table legs are easily
accessible. Now take the legs out of the box,
placing them as shown in the drawing (depending
on the table size).
2. Put the lid back on the box.
3. Position the isomo & wooden boards on top of
the box as shown in the drawing.
4. Put the tabletop on top of the wooden boards.
The top of the legs are now at about the same
height as the tabletop.
5. Now attach the legs to the tabletop.
6. Attach each leg with three M10 spring washers
and M10 nuts, but do not fully tighten them yet.
7. Before mounting the benches, remove the box
from under the table!
8. a. Slide the bench over the screw-thread of the
legs. TIP: To prevent lacquer damage, it is best to
Publicité
