CIAT CS2B Manuel D'installation page 10

Zone 1
Pre-set
½ÊÁǼ ½ÊÁǼ ʽ Ë½Ì ÇÍ»À  Ç
Start Number ÈÌÁÇÆ ¾ÇÊ ¹»À ½ÊÁǼ
Time
6:00 AM 1
Home ( )
8:00 AM 2
Away (
5:00 PM 3
Home ( )
10:00 PM 4
Sleep (
11:00 PM 5
Home ( )
00:00 AM 6
Sleep (
Zone 2
Pre-set
½ÊÁǼ ½ÊÁǼ ʽ Ë½Ì ÇÍ»À  Ç ÈÌÁÇÆ ¾ÇÊ ¹»À
Start Number ½ÊÁǼ
Time
6:00 1
Home ( )
8:00 2
Away (
12:00 3
Away (
14:00 4
Sleep (
18:00 5
Home ( )
22:00 6
Sleep (
Zone 3
Pre-set
½ÊÁǼ ½ÊÁǼ ʽ Ë½Ì ÇÍ»À  Ç ÈÌÁÇÆ ¾ÇÊ ¹»À
Start Number ½ÊÁǼ
Time
6:00 1
Home ( )
8:00 2
Away (
18:00 3
Home ( )
24:00 4
Home ( )
10
Çƽ Ǽ½ ÁĽÆÌ Ǽ½
ON OFF
ON OFF
)
ON OFF
ON OFF
)
ON OFF
ON OFF
)
Çƽ Ǽ½
ON
ON
)
ON
)
ON
)
ON
ON
)
Booster
Heater
¹ÄÄÇϽ¼
NO
NO
)
NO
YES
Here's how to connect your time periods with your
settings.
1. Open the lid.
2.
Press the days ( ) button at the bottom of
ÌÀ½ ÌÀ½ÊÅÇËÌ¹Ì ÇÍ ÏÁÄÄ Ë½½ ÌÇ
on the display.
3. Select one of the options (1 to 7 , 1 to 5 , 6
to 7 or individual day : 1, 2, 3, 4, 5, 6, 7) by
pressing the days ( ) button until you get
your desired option. Select 1 to 7 if your
individual day schedules are same.
4. When you have selected one of the
options (1 to 7, 1 to 5, 6 to 7 or individual
day: 1, 2, 3, 4, 5, 6, 7), press the
period ( ) button at the bottom of the
ÌÀ½ÊÅÇËÌ¹Ì  ÏÁÄÄ ¹ËÀ ÇÆ ÌÀ½ ¼ÁËÈĹÑ
5. Select the desired zone by pressing the
zone ( ) button repeatedly.
6. To change the hours in P1, press the start
time ( ) button at the bottom of the
screen.
7. ÇÍ ÏÁÄÄ Ë½½ ÌÀ½ ÀÇÍÊË ÁÆ
the screen. Press the up or down button
and stop on the desired time
8. To change the minutes, press start time
( ) button. You will see the minutes in
¹ËÀÁÆ¿ ÇÆ ÌÀ½ ˻ʽ½Æ
Press the up or down button and stop on
the desired time.
9. The "stop time" for period 1 (P1) is also the
"start time" for period 2 (P2). Use the
instructions in the next step to change the
start time for period 2.
10. Press the Touch 'N' Go button –
home ( ), away ( ) or sleep (
– you want to use during period 1 (P1) from
the row of buttons just below the display.
You will see triangle icon ( ) above the
button selected. This tells the thermostat
whether you are home, away, or sleep
during P1.
The thermostat will use the heating and
cooling temperature settings you've
selected for that Touch 'N' Go button. For
example, if your heating temperature
setting for home is 23 °C, the thermostat
will keep the heat at 23 during P1.
11. For zone 1 and zone 2: press the mode (M)
button on the left side of the display.
¾ ÌÀ½  Á»ÇÆ ) is displayed, Zone
mode is OFF, otherwise is ON.
12. For zone 1: press the hold ( ) button on the
left side of the display.
¾ ÌÀ½ ÁĽÆÌ Ǽ½ Á»ÇÆ ) is displayed,
Silent Mode is ON, otherwise is OFF.
13.
For zone 3: press the hold ( ) button on
the left side of the display.
¾ ºÇÇËÌ½Ê À½¹Ì½Ê Á»ÇÆ ) is displayed,
booster heater is enabled, otherwise is
disabled.
¹ËÀÁÆ¿
¹ËÀÁÆ¿ ÇÆ
)