Removing Jammed Staples; Accessories - Makita BST220 Manuel D'instructions

CAUTION:
• Do not hang the hook from the waist belt. Dropping the
stapler, which is caused by the hook accidentally
coming out of place, may cause misfiring and personal
injuries.
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool.
To install the hook, insert it into a groove in the tool
housing on either side and then secure it with a screw.
To remove, loosen the screw and then take it out. (Fig. 8)
OPERATION
Depth adjustment (Fig. 9)
If the staples are driven too deep or too shallow, adjust the
driving depth by turning the nut on the bottom of the tool.
For deeper driving of staples, turn the nut clockwise. For
shallower driving, turn the nut counterclockwise. Please
note the nut must be turned in increments of 90° (1/4 turn)
so that the groove on the nut runs parallel to the
magazine.
Driving staples (Fig. 10)
Place flat the opening of the tool from which staples are
fired on the material to be fastened and hold the tool firmly
against the material. Then pull the lever and then pull the
trigger fully to drive the staples. The grip is shaped so that
the tool head can be held down securely with index finger
and thumb. After driving a staple, be sure to release the
trigger fully.
When the head of driven staple remains above the
surface of material to be fastened, drive the staple while
holding the stapler head firmly. (Fig. 11)
NOTE:
• Using the stapler continuously with the head of driven
staples remaining above the surface of material to be
fastened may cause damage to the driver of the stapler
and stapler jamming etc.
Checking remaining staples (Fig. 12)
CAUTION:
• Do not operate the tool without staples. It shortens the
service life of the tool.
There is a convenient sight window on the right side of the
tool (when viewing the tool from the front). Use this sight
window to check if there are staples in the magazine.
When staples are not visible through the window, load
staples into the magazine.

Removing jammed staples

WARNING:
• Always make sure that the trigger are released and the
battery cartridge is removed before removing jammed
staples .
Remove the battery cartridge from the stapler. (Fig. 13)
Press the locking lever on the rear of the sub magazine
and slide the sub magazine backward.
Take out stuck staples that remain inside the opening that
staples are fired from as it appears.
6
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
• To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized Service Centers,
always using Makita replacement parts.

ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Staples
• Various type of Makita genuine batteries and chargers
• Safety goggles
For European countries only
Noise and Vibration
The typical A-weighted noise levels are
sound pressure level: 79 dB (A)
sound power level: 92 dB (A)
Wear ear protection.
The typical weighted root mean square acceleration value
2
is 4 m/s .
These values have been obtained according to EN792.
EC-DECLARATION OF CONFORMITY
Model; BST220, BST221
We declare under our sole responsibility that this product
is in compliance with the following standards of
standardized documents;
EN60745, EN55014 in accordance with Council
Directives, 2004/108/EC, 98/37/EC.
Tomoyasu Kato
Responsible Manufacturer:
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN
Authorized Representative in Europe:
Makita International Europe Ltd.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
CE 2008
Director
ENG047-1
ENH102-8