Bosch GSB 10 PROFESSIONAL Instructions D'emploi page 8

OBJ_BUCH-2 609 140 313-003.book Page 3 Thursday, July 21, 2005 2:20 PM
Tool Specifications
Hammer Drill
Article number
Rated power input
Output power
No-load speed
Rotational speed under load
(max.)
Impact rate
Rated torque
Speed preselection
Right/left rotation
Spindle collar dia.
Max. drilling dia.
Concrete
Steel
Wood
Chuck clamping range
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for nominal voltages [U] of 230/240 V. For lower voltages and models for specific countries, these
values can vary.
Please observe the article number on the type plate of your power tool. The trade names of individual tools may vary.
Noise/Vibration Information
Measured values determined according to EN 60745.
Typically the A-weighted noise levels of the machine
are: sound pressure level 93 dB(A); sound power level
104 dB(A). Measurement uncertainty K=3 dB.
Wear hearing protection!
The typically weighted acceleration is 16 m/s
Assembly
Auxiliary Handle (see figure A)
(GSB 13/GSB 13 RE/GSB 16/GSB 16 RE)
Operate your power tool only with the auxiliary
handle 9.
The auxiliary handle 9 can be set to any position for a
secure and low-fatigue working posture.
Turn the wing bolt for adjustment of the auxiliary handle
8 in counterclockwise direction and set the auxiliary
handle 9 to the required position. Then tighten the wing
bolt 8 again in clockwise direction.
2 609 140 313 • 21.7.05
All manuals and user guides at all-guides.com
GSB ... 10
PROFESSIONAL
3 601 ... B16 0..
W 500
W 250
rpm 2600 0–2600
rpm 1610
bpm 25700
Nm 1.5
mm 43
mm 10
mm
mm 20
mm 1.5–10 1.5–10 1.5–13 1.5–13 1.5–13 1.5–13
kg 1.5
/II
Adjusting the Drilling Depth (see figure A)
The required drilling depth X can be set with the depth
stop 10.
Press the button for the depth stop adjustment 7 and
insert the depth stop into the auxiliary handle 9.
Pull out the depth stop until the distance between the
tip of the drill bit and the tip of the depth stop corre-
spond with the desired drilling depth X.
2
.
Changing the Tool
Before any work on the power tool itself, pull the
mains plug.
Keyless Chuck (see figure B)
Tightly hold the rear sleeve of keyless chuck 1 and turn
the front sleeve counterclockwise until the tool can be
inserted. Insert the tool.
Tightly hold the rear sleeve of the keyless chuck 1 and
firmly turn the front sleeve clockwise by hand until the
locking action is no longer heard. This automatically
locks the drill chuck.
The locking is released again to remove the tool when
the front sleeve is turned in the opposite direction.
English–3
10 RE 13 13 RE
B16 1.. B17 0.. B17 1..
500 600 600
250 301 301
2800 0–2800
1610 1570 1570
25700 25070 25070
1.5 1.8 1.8
– – –
– –
43 43 43
10 13 13
8 8 10 10
20 25 25
1.5 1.7 1.7
/II /II /II
16 16 RE
B18 0.. B18 1..
701 701
351 351
3000 0–3000
1640 1640
26270 26270
2.0 2.0
– –
–
43 43
16 16
12 12
30 30
1.9 1.9
/II /II