Important Safety Instructions - Makita AF505N Manuel D'instruction

ENGLISH (Original instructions)
SPECIFICATIONS
Min. hose diameter
Dimensions (L X H X W)
• Due to our continuing program of research and development, the specifications herein are subject to change with-
out notice.
• Note: Specifications may differ from country to country.

Important safety instructions

For personal safety and proper operation and main-
tenance of the tool, read this instruction manual
carefully before using the tool.
WARNING: WHEN USING THIS TOOL, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED TO REDUCE THE RISK OF PERSONAL
INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
Personal Protective Equipment
1. Always wear safety glasses to avoid eye injury
from dust or fasteners. The safety glasses should
conform with the requirements of ANSI Z87.1.
WARNING:It is an employer's responsibility
to enforce the use of safety eye protection
equipment by the tool operators and by other
persons in the immediate working area.
Wear hearing protection to protect your ears
2.
against exhaust noise and head protection.
Also wear light but not loose clothing. Sleeves
should be buttoned or rolled up. No necktie
should be worn.
Flammable Atmospheres
1. Do not operate tool in explosive atmospheres,
such as in the presence of flammable liquids,
gases or combustible dust.
Tool modification
1. The tool should not be modified unless autho-
rized in the tool manual or approved in writing
by the tool manufacturer.
Tool maintenance
1. Refer to the tool maintenance instructions for
detailed information on the proper mainte-
nance of a tool.
Recommended fasteners and accessories
1. Use only fasteners made or recommended by
the tool manufacturer, or fasteners that per-
form equivalently to those recommended by
the manufacturer.
Use only accessories made or recommended
2.
by the tool manufacturer, or accessories that
perform equivalently to those recommended
by the manufacturer.
Model
Air pressure
Nail length
Nail capacity
Net weight
0.39 - 0.78 MPa (60 - 115 PSIG)
15 mm (5/8") - 50 mm (2")
260 mm X 237 mm X 64 mm (10-1/4" X 9-5/8" X 2-1/2")
Inspect tool before operating to:
1. Use only power source specified in the instruc-
tion manual.
Operate the tool within the specified air pres-
sure on the tool label for safety and longer tool
life. Do not exceed the recommended max.
operating pressure. The tool should not be
connected to a source whose pressure poten-
tially exceeds 1.37 MPa (200 PSIG).
2. Never use the tool with other than compressed
air. If bottled gas (carbon dioxide, oxygen,
nitrogen, hydrogen, air, etc.) or combustible
gas (hydrogen, propane, acetylene, etc.) is
used as a power source for this tool, the tool
will explode and cause serious injury.
3. Always check the tool for its overall condition
and loose screws before operation. Tighten as
required.
4. Make sure all safety systems are in working
order before operation. The tool must not
operate if only the trigger is pulled or if only
the contact element is pressed against the
wood. It must work only when both actions are
performed. Test for possible faulty operation
with fasteners unloaded and the contact ele-
ment in fully pulled position.
5. Always check contact element as instructed in
this manual. Fasteners may be driven accidentally
if the safety mechanism is not working correctly.
Operating controls
1. Do not use a tool with missing or damaged
safety warning label(s.)
A tool that is not in proper working order must
2.
not be used. Tags and physical segregation
shall be used for control.
Do not remove, tamper with, or otherwise
3.
cause tool operating controls to become
inoperable.
Do not operate tool if any portion of the tool
4.
operating controls is inoperable, discon-
nected, altered, or not working properly.
Tool handling
Only persons who have read and understand
1.
the tool operating/safety instructions should
operate the tool.
Always assume that tool contains fasteners.
2.
2 ENGLISH
AF505N
100 pcs.
6.5 mm (1/4")
1.4 kg (3.01 lbs)